GB-1
GB-2
GB-3
PRODUCT OVERVIEW
UNPACKING
Remove all packaging from the kettle. Retain the packaging. If you dispose
of it please do so according to local regulations.
The following items are included:
FIRST TIME USE
Clean your kettle by boiling a full kettle of water twice and then discarding
the water.
KEEPING THE MAINS CABLE TIDY
Extend the mains cable in the kettle stand to
the required length. Locate the mains cable
in one of the slots in the stand. For safety it
is recommended that the length of exposed
mains cable is kept as short as possible.
Place the kettle stand on a firm level surface
and plug in the mains plug at a standard
mains socket (240 Volt 13 Amp rated).
Instruction Manual
(
Part number: L17KBS10-001
)
The kettle
If items are missing or damaged, please contact Partmaster (UK only)
Tel. 0844 800 3456 for assistance.
This kettle must only be used with the stand provided.
DESCALING THE KETTLE
Depending on the hardness of the water
in your area, limescale may be deposited
on the heating element and the inside of
the kettle. This normal build-up is not
harmful to health but an excessive
amount of scale may affect the
performance of the kettle.
To descale, fill the kettle with distilled
water up to three-quarters of the Max
level and bring the water to boil. After the
kettle has switched off, add a descaling
solution following the manufacturers
instructions. Never attempt to descale the
kettle by chipping or scraping with a
sharp implement.
CLEANING THE KETTLE
The kettle exterior should be cleaned with a soft damp cloth. Do not use
abrasive cleaners or scouring pads which may damage the finish of the kettle.
Never immerse the kettle or kettle stand in water and always keep the electrical
contacts dry. Disconnect from the mains before cleaning the kettle stand.
CLEANING THE REMOVABLE SCALE FILTER
To prevent loose particles of limescale being poured into your beverage, your
kettle is fitted with a scale filter. You may remove the filter and fit it back in
after cleaning.
FILLING THE KETTLE
Slide the switch to open the lid and fill the kettle with the required amount of
water.
Do not exceed the maximum fill level (Max 1.7L) as indicated inside the kettle
and not less than the minimum fill level (Min 0.5L).
Do not insert any foreign objects or allow any liquid to spill into the Power
Connector Hole.
WHEN THE WATER HAS BOILED
The kettle will automatically switch off . The
light inside the kettle will go off.
Ensure that the switch is not
obstructed and the lid is firmly closed.
The kettle will not turn off if the
switch is obstructed or if the lid is
open.
If there is insufficient water in the kettle, the automatic safety cut-out
will operate. If this happens, allow the kettle to cool for ten minutes before
refilling with cold water and re-boiling.
If the kettle is overfilled, boiling water may be ejected from the spout and
cause scalding.
After removing the kettle, there may be some water on the surface of the
stand. This is condensation from the steam that causes the kettle to
automatically switch off after boiling. This is normal and should not be a
cause for alarm.
Never open the lid while the water is
boiling. The steam coming out from
the kettle is very hot.
SWITCHING ON
Place the kettle on the stand and press the
power switch downward. The light inside
the kettle will illuminate to indicate that the
kettle is heating. This is visible through the
glass lid.
Stand
Spout
Lid
Fill Level
Power Switch
Open Button
Handle
Power Connector Hole
To remove the filter, open the lid,
press and lift up the filter from the
bracket at the spout.
To fit in the filter, open the lid, place
the filter inside the bracket at the
spout, locate the 3 slots shown by the
arrows above and fit it in place.
