background image

DMUI-HSM - MANUAL // PAGE 14

7  SYSTEM INFORMATION

When a DMU-HSM Handset is installed alongside the DYNAMIC MOTION system, system information is 
communicated via flashes of the LED Signal Light. Possible signals are as follows: 

Signal

Message

Required Actions

No Light

System operating normally

Operate the DM System as normal.

System not connected 
properly

See Chapter 4 for connection instructions. 

Red Light Blinking

System Error Warning

Release all Keys and wait for 5 seconds. Then, 
try to repeat the action again.

Disconnect all components from the Power 
Hub. 

Disconnect the Power Hub from the Mains. 
Check the Power Hub for overheating. Let cool 
if necessary.  
Check all cable connections and reconnect the 
system. 

If problem persists:

Perform a Position Reset Procedure (Chapter 
4.7).
Contact LOGICDATA

Green Light Blinking

System Start-up

Wait until the LED has stopped blinking to 
continue.
Do not press any buttons.

Reset in Progress

Duty Cycle Exceeded

Collision Detected (ISP)

Remove the obstruction from the Table System. 
Remove unnecessary loads from the Table Top
Operate the DM System as normal.

Green Light Flashing 
Rapidly

Position Reset Required.

Perform a Position Reset Procedure (System 
Manual, Chapter 4.7).

NOTICE

Do not operate the DYNAMIC MOTION system if problems persist. Contact LOGICDATA 

for further information. 

Summary of Contents for DYNAMIC MOTION DMUI-HSM


















Reviews: