LOFTNESS OS 170 Owner'S Manual And Parts Book Download Page 10

Page: 10 / 76

OS 170 Fertilizer Spreader OM

Features

Spread Pattern

• Dual (25 ft.) stainless steel spinners deliver a

spread pattern using a 100% overlapping triangular
pattern.

• Spread pattern up to 40 ft.

Fixed Axles

• 42 in. (106.7 cm) track setting.

Adjustable Height Hitch

• Moveable clevis accommodates wide range of

drawbar heights.

• Allows for leveling of spreader.

Integral Hitch

• Hitch is integral to frame.

Conveyor Drive

• Hydraulic drive, variable rate ready.

• Chain drive, fixed rate, adjustable with gate.

Obstruction Free Interior

• No internal gussets/plates to catch fertilizer.

Spinner Drive

• Hydraulic drive

Introduction

Options

Bander

• Optional banding attachment - Adjustable wings for

placing fertilizer in strips

Summary of Contents for OS 170













































































Search results

Summary of Contents for OS 170

Reviews:

Related manuals for OS 170

Brands by name

Popular brands

LOFTNESS OS 170, Owner'S Manual And Parts Book

Search results

Summary of Contents for OS 170

Reviews:

Related manuals for OS 170

Brands by name

Popular brands