LOFTNESS 15 Owner'S Manual And Parts Book Download Page 34

Page: 34 / 106

Windrow Crop Shredder OM

Insert drawbar pin (1), secure with safety locking pin.

Connect safety chain (2).

Pull retaining pin (3) on PTO holder and move arm (4) out
of the way to release tractor end of PTO shaft.

Return arm and retaining pin back into position.

Operating Instructions

Transport to Working Configuration

Procedure (Cont'd)

Neatly wrap hydraulic hoses and secure coupler ends
into storage rack on top of shredder.

Rotate transport jack (14) into position.

Using jack, raise the transport hitch enough to remove
drawbar pin (15).

Remove safety chain (16).

Connecting to the Operation Hitch

Remount tractor and move into position to connect to
operation hitch.

Once aligned, turn off tractor and dismount.

DANGER:

Failure to turn the tractor off before

connecting the hydraulic lines and PTO shaft
could result in serious injury or death.

Summary of Contents for 15











































































































Search results

Summary of Contents for 15

Reviews:

Related manuals for 15

Brands by name

Popular brands

LOFTNESS 15, Owner'S Manual And Parts Book

Search results

Summary of Contents for 15

Reviews:

Related manuals for 15

Brands by name

Popular brands