background image

1.  Please Observe the Following

1

1.1 Emphasized Sections

Warning!

Refers to safety regulations and required safety measures that protect the operator or other 
persons from injury or danger to life.

Caution!

Emphasizes what must be done or avoided so that the Unit or other property is not damaged.

Notice:

Gives recommendations for better handling of the Unit during operation or adjustment as well as
for service activities.

1.2 For Your  Safety

For safe and successful operation of the Unit, read these instructions completely. If the
instructions are not observed, the manufacturer can assume no responsibility. Be sure to retain
this manual for future reference.

WARNING! 

Do not use the Unit to extract easily flammable or explosive gases.

WARNING! 

Do not use the Unit to extract corrosive substances.

WARNING! 

Do not expose the connecting cable to heat, oil, or sharp edges.

WARNING! 

Make sure the Unit stands stable and secure.

WARNING! 

Use only original equipment filters.

WARNING! 

Do not operate the Unit without filter inserts. Contaminants in the extracted air will damage 
the blower.

WARNING! 

Always disconnect the power supply before servicing the Unit.

WARNING! 

Never cover intake or exhaust openings.

WARNING! 

This system is equipped with automatic reset overload protection (thermal switch or overload
relay), which may cause the Unit to restart automatically. See page 4.

WARNING! 

Observe general safety regulations for the handling of chemicals such as Loctite

®

adhesives 

and sealants. Observe the manufacturer’s instructions as stated in the Material Safety Data 
Sheet (MSDS).

While under warranty, the Unit may be repaired only by an authorized Loctite service
representative.

1.3 Unpacking and Inspection

Carefully unpack the Loctite

®

Air Filtration System and examine the items contained in the carton.

Inspect the Unit for any damage that might have occurred in transit. If such damage has occurred,
notify the carrier immediately. Claims for damage must be made by the consignee to the carrier
and should be reported to the manufacturer.

Summary of Contents for 98276













Reviews: