61
Set domestic hot water (DHW) operation
Verify DHW mode
Th
ere are two (2) modes of operation for DHW. In Normal
Mode, when a DHW demand begins, the control will start
the DHW pump, turn off the boiler pump (if running), and
modulate to bring the outlet temperature to the DHW boiler
set point. Th
e maximum fi ring rate may be limited in this
mode if desired.
In Zone Mode it is assumed that the indirect DHW tank is
piped as a zone on the primary loop. When a DHW demand
begins, the control will turn on the DHW pump output, and
raise the system temperature set point to the DHW boiler set
point (if higher). Th
e boiler pump will be turned on. Th
e
system pump may be forced on, forced off , or not changed,
depending on the System Pump Mode selected (reference
the Knight XL Service Manual for details). In this mode, any
low temperature zones (such as radiant heating) may need
additional controls to limit the water temperature sent to
those zones.
Set DHW boiler target temperature
When in the DHW Mode, the control will modulate to
maintain the boiler outlet temperature or system supply
temperature to a set point. Th
is set point is set at the factory
to 180°F. If a diff erent set point is desired, the appropriate
parameter in the control must be changed. See the Knight XL
Service Manual for a detailed explanation of this procedure.
Set maximum DHW fan speed
If the rated input of the indirect tank is less than the
maximum output of the boiler, change the maximum DHW
fan speed setting to limit the boiler output accordingly, see
the Knight XL Service Manual for a detailed explanation of
this procedure.
NOTICE
Th
e internal clock does not adjust for
Daylight Savings Time and therefore, will
require a manual adjustment.
Confi guration of the cascade
10
Start-up
(continued)
7. Turn the NAVIGATION dial to adjust the minutes. Press
the NAVIGATION dial.
8. Turn the NAVIGATION dial to adjust the month. Press
the NAVIGATION dial.
9. Turn the NAVIGATION dial to adjust the date. Press the
NAVIGATION
dial.
10. Turn the NAVIGATION dial to adjust the year. Press the
RIGHT SELECT [SAVE] key.
11. Press the RIGHT SELECT [HOME] key.
Please note that the brackets ([]) denote
screen status.
NOTICE
Set clock
When installed in a Cascade system, the individual controls must
be programmed for cascade operation. Th
is is accomplished by
accessing the control parameters.
Press the [MENU] key for at least fi ve (5) seconds. Input the
Installer code as described in the Knight XL Service Manual.
Once the control parameters have been accessed, use the
NAVIGATION DIAL to select the Control Mode parameters.
Press the NAVIGATION DIAL to access these parameters.
Rotate the NAVIGATION dial to select the parameter
“Cascade Address”. Press the NAVIGATION dial to access
this parameter. Each appliance in the Cascade system must be
programmed with its own address. Th
e boiler designated as the
Leader will have an address of 0. Th
e remaining boilers in the
Cascade will be Members and have addresses from 1 - 7. Rotate
the NAVIGATION dial to select the appropriate address. Press
the RIGHT SELECT [SAVE] key.
Press the RIGHT SELECT [HOME] key to upload the address
into the control. Repeat this procedure for all boilers in the
Cascade, designating the Leader control and the Member
controls.
Please note that the brackets ([]) denote
screen status.
NOTICE
Th
e SMART SYSTEM control has a built-in clock that it
uses for its night setback feature and for logging events. Th
is
clock must be set when the boiler is installed, and anytime the
boiler has been powered off for more than 4 hours. Use the
following procedure to set the clock:
1. Press and hold the LEFT SELECT [MENU] key for at
least 5 seconds.
2. The display changes to read [PASSWORD],
with four (4) zeros below it.
3. Press the RIGHT SELECT [SAVE] key.
4. Th
e display will then show a menu with the time and
date and temperature unit.
5. Press the NAVIGATION dial twice.
6. Turn the NAVIGATION dial to adjust the hours. Press
the NAVIGATION dial.
Installation & Operation Manual
Th
e clock is automatically updated whenever a PC is connected
and the Win_Pro-Installer program is started.
