11
LITTLE
WONDER
PRO VAC
SET-UP INSTRUCTIONS
UNPACKING THE UNIT
1. Remove Collector assembly, Nozzle assembly, and
debris bag from the top section of the package.
2. Remove cardboard insert.
3. Cut away short side of the box and fold down.
4. Roll base unit out of the box.
ASSEMBLY (S
ee Figures on page 11)
1. Attach the
collector assembly
to the base unit:
•Bolt the collector assembly to the frame with 4 sets
of bolts, nuts, and 3 washers. Attach rope guide
with upper right bolt.
•Slide the rectangular end of the collector over
the housing and mount the flange with 2 sets of
washers and nuts.
2. Attach the throttle cable bracket to the handle with a
1/4-20 thread rolling screw A. Tighten until snug, but
do not overtighten. Intall throttle cable assembly to
handle with 1/4-20x2 bolt, 2 washers, and 1/4 nylon
locknut.
•Secure throttle cable to handle with
cable ties
in 2
places.
3. Install the
band clamp
into the
debris bag
(wear
gloves when handling band clamp):
•Slide the bracket end of the band clamp through the
left side opening of the sleeve on the debris bag
until it emerges from the right side.
•Feed the tail end of the band (on the clasp side)
behind the bracket in the sleeve.
•Pinch the wire form on the clasp together and
connect it through 2 holes in the adjustment bracket
such that it will close tightly over the collector.
4. Connect the
debris bag
by placing it over the bottom
lip of the
collector
and closing the clasp to secure the
bag. Adjust the clasp wire form to the appropriate hole
position on the bracket to insure a tight fit. If the bag
will not fit tight within the range of the 3 adjustment
holes, insert the bag
seal strap
:
•Unhook the wire form from the bracket.
•Pull the tail end of the band back out from behind
the bracket.
•Feed one end of the
seal strap
behind the metal
band and through the channel to the other side.
•Tuck the other end of the
seal strap
behind the
bracket (overlapping the lead end of the
seal strap
).
•Feed the tail end of the
band clamp
behind the
bracket (overlap the
seal strap
).
•Connect the wire form to the appropriate holes in the
bracket and secure the debris bag to the collector.
5. Attach
nozzle assembly
to base unit:
•Attach one end of the
hose
to the nozzle assembly
with the
bridge clamp Assembly.
•Slide the other end of the
hose
over the edge of the
inlet on the
front plate.
•Hook one side of the
nozzle bracket
over the front
axle.
•Bend the other end of the nozzle bracket inward to
hook it over the axle and engage the pins on the
wheel bracket
with the slots on the
nozzle bracket.
•Secure the hose to
front plate
inlet with the
bridge
clamp.
•Attach the
nozzle cable
end fitting through the hole
in the
nozzle bracket.
6. To remove
nozzle assembly
(for purposes of storage,
or clearing blockages):
•Turn engine off and disconnect spark plug.
•Loosen
hose clamp
on the
front plate
with flathead
screwdriver or 5/16 wrench.
•Slide hose off of
front plate
inlet.
•Bend one side of
nozzle bracket
inward and twist
the
assembly
to remove the hook from the axle.
•Twist back and lift to remove the other side of
nozzle bracket
from the axle.
LIFTING LUG
The Little Wonder Pro Vac includes a convenient lifting
lug
A
on top of the fan housing that can be used to lift
the unit. This lug can only hold up to a total of 250 lbs
(115 kg).
Summary of Contents for 5612-00-59
