page 3
INSTALLATION INSTRUCTIONS
For Wet Location compliance, fixture must be properly sealed!
Apply
caulking to the perimeter of the fixture between the housing and the wall (top and
two sides) leaving the bottom side clear of any caulking. Caulking will prevent
any water coming down the wall from entering the fixture.
Note:
Do not apply
caulking on the bottom.
Make sure all wiring access holes are sealed with weatherproof silicone
sealant (not included)!
Photocontrol switch
This wall pack is designed to be mounted to a recessed junction box or
directly to a flat surface.
CAUTION: DO NOT MOUNT WITH LIGHT AIMING UP, TO AN
EXTERNAL JUNCTION BOX, OR OVER RAISED RIBS AS FOUND IN
CORRUGATED SIDING
Remove fixture components and parts pack.
Check to ensure all parts are
included.
Note:
Account for small parts and destroy packing material, as these
may be hazardous to children.
Turn OFF Power at circuit breaker box.
CAUTION:
Do not rely on wall switch alone to turn off power
Table - 1 Choose Settings (Optional)
Switchable Photocontrol
ON*/OFF
Color Temperature
3000K/4000K*/5000K
Adjustable Lumens
1650*
1200
1000
850
*Factory Setting
1. Remove the door assembly (2) from rear housing.
Remove and retain
Decorative Plugs. Loosen two screws (3) on the front, open door, unhook tether
and separate door assembly from rear housing.
Note:
Do not remove screws
completely
2.
For junction box mounting, prepare the rear housing for installation by
removing the knockout holes as needed, thread house supply wires through the
center hole in rear housing and
secure the rear housing to junction box
using
mounting screws (5) provided. See Figure C for detail
3
.
Reconnect door to rear housing and secure with tether.
CAUTION: WIRING AND FIXTURE OPERATION
Make sure power is turned off.
4. Ground fixture
using wire nut to connect the (copper or green) supply ground
wire & the green fixture ground wire.
Note:
If wiring does not include a ground
wire, consult your local electrical code for approved grounding methods.
For proper connection, place wire nut over wires
and twist clockwise until tight.
5. Connect supply wires
using wire nut to connect the black fixture wire to the
black power supply wire and the white fixture wire to the white (neutral) supply
wire. Bundle leads and secure to rear housing with provided wire tie to ensure no
wires are pinched when closing the door.
6. Close Door and tighten screws to 15-20 in-lbs.
Do not over-tighten the
screws.
Note:
make sure no wires are pinched before tightening screws.
Install
Decorative plugs to cover screw heads.
7.
Luminaire is preset to 1650
lumens, 4000K CCT, and PE in the On position. If
desired, change settings by adjusting the switch. See Figure A/Switch.
8.
Turn on electricity at fuse or circuit breaker box and verify success of
installation.
FIXTURE PARTS LIST
Description
Quantity
1) Rear Housing ................................................................................................
1
2) Door Assembly .............................................................................................
1
3) 1” 10-24 Screws ............................................................................................
2
4) Tether ............................................................................................................
1
5) 5/8” 8-32 Mounting screws*
5/8” 8-32 Mounting screws* ........................................................................
2
6) Wire Nuts*
Wire Nuts* ....................................................................................................3
*Contained in parts packs
SUPPLY HOT WIRE (BLACK)
/ CABLE CALIENTE (NEGRO)
/ FIL DE PHASE (NOIR)
SUPPLY NEUTRAL WIRE (WHITE)
/ CABLE NEUTRO (BLANCO)
/ FIL DE NEUTRE (BLANC)
SUPPLY GROUND WIRE
/ CABLE DE PUESTA A TIERRA
/ FIL DE TERRE
Figure A
Figure B
Color temperature switch
Lumen Switch
1) Rear housing
4) Tether
5) Switch
3) Screws
2) Door Assembly
