page 2
•
To reduce the risk of death, personal injury or property damage from fire, electric
shock, falling parts, cuts/abrasions, and other hazards please read all warnings
and instructions included with and on the fixture box and all fixture labels.
•
Before installing, servicing, or performing routine maintenance upon this
equipment, follow these general precautions.
•
Commercial installation, service and maintenance of luminaires should be
performed by a
qualified licensed electrician
.
•
For Residential installation: If you are unsure about the installation or
maintenance of the luminaires, consult a qualified licensed electrician and check
your local electical code.
•
Maintenance of the luminaires should be performed by person(s) familiar with
the luminaires’ construction and operation and any hazards involved. Regular
fixture maintenance programs are recommended.
•
This fixture is intended to be connected to a properly installed and grounded UL
listed junction box.
•
It will occasionally be necessary to clean the outside of the refractor/lens.
Refractor/lens should be washed in a solution of warm water and any mild, non-
abrasive household detergent, rinsed with clean water and wiped dry. Should
optical assembly become dirty on the inside, wipe refractor/lens and clean in
above manner, replacing damaged gaskets as necessary.
• DO NOT INSTALL DAMAGED PRODUCT!
This luminaire has been
properly packed so that no parts should have been damaged during transit.
Inspect to confirm. Any part damaged or broken during or after assembly should
be replaced.
•
Recycle: For information on how to recycle LED electronic products, please
visit www.epa.gov.
•
These instructions do not purport to cover all details or variations in equipment
nor to provide every possible contingency to meet in connection with installation,
operation, or maintenance. Should further information be desired or should
particular problems arise which are not covered sufficiently for the purchaser’s
or owner’s purposes, this matter should be referred to Acuity Brands Lighting,
Inc.
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS!
WARNING
RISK OF ELECTRIC SHOCK
CAUTION
RISK OF INJURY
CAUTION
RISK OF FIRE
CAUTION
RISK OF PRODUCT DAMAGE
WARNING
RISK OF BURN
►
Disconnect or turn off power before installation or servicing.
►
Verify that supply voltage is correct by comparing it with the luminaire label
information.
►
Make all electrical and grounded connections in accordance with the National
Electrical Code (NEC) and any applicable local code requirements.
►
All wiring connections should be capped with UL approved wire connectors.
►
Wear gloves and safety glasses at all times when removing luminaire from
carton, installing, servicing or performing maintenance.
►
Avoid direct eye exposure to the light source while it is on.
►
Keep combustible and other materials that can burn, away from lamp/lens.
►
Do not operate in close proximity to persons, combustible materials or substances
affected by heat.
►
Never connect components under load.
►
Do not mount or support these fixtures in a manner that can cut the outer jacket
or damage wire insulation.
►
Controls for dimming, auto-sensing, or remote control of a luminaire that are
not factory-wired to the luminaire must be checked for compatibility with the
luminaire prior to installation. LED fixtures must be powered directly off a
switched circuit.
►
Unless individual product specifications deem otherwise: Do not restrict fixture
ventilation. Allow for some volume of airspace around the fixture. Avoid
covering LED fixtures with insulation, foam, or other material that will prevent
convection or cooling.
►
Unless individual product specifications deem otherwise: Do not exceed fixtures
maximum ambient temperature.
►
Only use fixture in its intended location.
►
LED products are Polarity Sensitive. Ensure proper Polarity before installation.
►
Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal
grounding equipment must be worn during all installation or servicing of unit.
►
Do not touch individual electrical components as this can cause ESD, shorten
lamp life, or alter performance.
►
Some components inside the fixture may not be serviceable. In the unlikely
event your unit may require service, stop using the unit immediately and contact
an ABL representative for assistance.
►
Changes or modifications not expressly approved by Acuity Brand Lighting
could void the authority to operate the equipment.
►
Always read the fixtures complete installation instructions prior to installation
for any additional fixture specific warnings.
►
Always ensure that the electrical distribution system is up to NEC (and applicable
local code) requirements.
►
Verify that power distribution system has proper grounding. Lack of proper earth
ground can lead to fixture failure and may void warranty.
►
Allow lamp/fixture to cool before handling. Do not touch enclosure, lens or light
source.
►
Do not exceed maximum wattage marked on luminaire label.
►
Follow all manufacturer’s warnings, recommendations and restrictions including
but not limited to: driver type, burning position, mounting locations/methods,
replacement and recycling.
All luminaires that contain electronic devices that generate frequencies above 9kHz
from any component within the luminaire comply with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that
may cause undesired operation.
This device complies with Part 15 of the FCC Rules but may cause interference
with cordless and cell phones, radios, televisions, and other electronic devises.
To correct the problem, move the device away from the luminaire or plug into a
different outlet. This product may cause interference to radio equipment and should
not be installed near maritime safety communication equipment or other critical
navigation or communications equipment operation between. 0.45-30MHz.
5-YEAR LIMITED WARRANTY
Register your warranty on www.acuitybrands.com/resources/warranty. Your
prompt product registration confirms your right to the protection available under
the terms and conditions of your Lithonia Lighting warranty.
Failure to follow any of these instructions could void product warranties. For a
complete listing of product Terms and Conditions, please visit www.acuitybrands.
com. Acuity Brands Lighting, Inc. assumes no responsibilities for claims arising
out of improper or careless installation or handling of its products.
