page 2
• To reduce the risk of death, personal injury or property damage from fi re,
electric shock, falling parts, cuts/abrasions, and other hazards please
read all warnings and instructions included with and on the fi xture box
and all fi xture labels.
• Before installing, servicing, or performing routine maintenance upon this
equipment, follow these general precautions.
• Commercial installation, service and maintenance of luminaires should
be performed by a qualifi ed licensed electrician.
• For Residential installation: If you are unsure about the installation or
maintenance of the luminaires, consult a qualifi ed licensed electrician
and check your local electical code.
• Maintenance of the luminaires should be performed by person(s)
familiar with the luminaires’ construction and operation and any hazards
involved. Regular fi xture maintenance programs are recommended.
• This fi xture is intended to be connected to a properly installed and
grounded UL listed junction box.
• It will occasionally be necessary to clean the outside of the refractor/
lens. Refractor/lens should be washed in a solution of warm water and
any mild, non-abrasive household detergent, rinsed with clean water and
wiped dry. Should optical assembly become dirty on the inside, wipe
refractor/lens and clean in above manner, replacing damaged gaskets
as necessary.
• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been
properly packed so that no parts should have been damaged during
transit. Inspect to confi rm. Any part damaged or broken during or after
assembly should be replaced.
• Recycle: For information on how to recycle LED electronic products,
please visit www.epa.gov.
• These instructions do not purport to cover all details or variations
in equipment nor to provide every possible contingency to meet in
connection with installation, operation, or maintenance. Should further
information be desired or should particular problems arise which are not
covered suffi ciently for the purchaser’s or owner’s purposes, this matter
should be referred to Acuity Brands Lighting, Inc.
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW THESE SAFETY INSTRUCTIONS!
WARNING
RISK OF ELECTRIC SHOCK
CAUTION
RISK OF INJURY
CAUTION
RISK OF FIRE
CAUTION
RISK OF PRODUCT DAMAGE
WARNING
RISK OF BURN
►
Disconnect or turn off power before installation or servicing.
►
Verify that supply voltage is correct by comparing it with the luminaire
label information.
►
Make all electrical and grounded connections in accordance with
the National Electrical Code (NEC) and any applicable local code
requirements.
►
All wiring connections should be capped with UL approved wire
connectors.
►
Wear gloves and safety glasses at all times when removing luminaire
from carton, installing, servicing or performing maintenance.
►
Avoid direct eye exposure to the light source while it is on.
►
Keep combustible and other materials that can burn, away from lamp/
lens.
►
Do not operate in close proximity to persons, combustible materials or
substances affected by heat.
►
Never connect components under load.
► Do not mount or support these fi xtures in a manner that can cut the outer
jacket or damage wire insulation.
► Unless individual product specifi cations deem otherwise: Never connect
an LED product directly to a dimmer packs, occupancy sensor, timing
device, or other related control devices. LED fi xtures must be powered
directly off a switched circuit.
► Unless individual product specifi cations deem otherwise: Do not restrict
fi xture ventilation. Allow for some volume of airspace around the fi xture.
Avoid covering LED fi xtures with insulation, foam, or other material that
will prevent convection or cooling.
► Unless individual product specifi cations deem otherwise: Do not exceed
fi xtures maximum ambient temperature.
► Only use fi xture in its intended location.
►
LED products are Polarity Sensitive. Ensure proper Polarity before
installation.
► Electrostatic Discharge (ESD): ESD can damage LED fi xtures. Personal
grounding equipment must be worn during all installation or servicing
of unit.
►
Do not touch individual electrical components as this can cause ESD,
shorten lamp life, or alter performance.
► Some components inside the fi xture may not be serviceable. In the
unlikely event your unit may require service, stop using the unit
immediately and contact an ABL representative for assistance.
► Changes or modifi cations not expressly approved by Acuity Brands
Lighting could void the authority to operate the equipment.
► Always read the fi xtures complete installation instructions prior to
installation for any additional fi xture specifi c warnings.
► Allow lamp/fi xture to cool before handling. Do not touch enclosure, lens
or light source.
►
Do not exceed maximum wattage marked on luminaire label.
►
Follow all manufacturer’s warnings, recommendations and restrictions
including but not limited to: driver type, burning position, mounting
locations/methods, replacement and recycling.
►
Use only lamps that comply with ANSI standards.
This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when used in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
1-YEAR LIMITED WARRANTY
Failure to follow any of these instructions could void product warranties.
For a complete listing of product Terms and Conditions, please visit www.
acuitybrands.com. Acuity Brands Lighting, Inc. assumes no responsibilities
for claims arising out of improper or careless installation or handling of its
products.