Litex RG52BNK5L Installation Manual Download Page 5

page 4

Install hanging bracket to outlet box using 
original screws, spring washers and flat washers 
provided with new or original outlet box.* Pull 
electrical wiring from outlet box through center 
hole in the hanging bracket. 

*

Note

: It is very important that you use the proper 

hardware when installing the hanging bracket as 
this will support the fan.  

WARNING

: Turn off circuit breakers to current 

fixture from breaker panel and be sure switch is 
turned to the OFF position.

 
Lift motor assembly to hanging bracket and slide 
slot at one end of motor assembly over j-hook on 
hanging bracket. This will allow motor assembly to 
hang out of the way while wiring.

Tip

: Seek the help of another person to hold the 

stepladder in place and to lift the fan up to you once 
you are set on the ladder.

 

CAUTION

Be sure outlet box is properly grounded  

and that a ground wire (

GREEN

 or Bare) is present.

 

Make sure all electrical connections comply with Local 
Codes or Ordinances and the National Electrical Code. 
If you are unfamiliar with electrical wiring or if the 
house/building wires are different colors than those 
referred to below, please use a qualified electrician.

 
When fan is secured in place on the hanging 
bracket, electrical wiring can be made

 

as follows:

Connect 

BLACK

 and 

BLUE

 wires from fan to 

BLACK

 

wire from ceiling with wire connector provided.
Connect 

WHITE

 wire from fan to 

WHITE

 wire from 

ceiling with wire connector provided.
Connect all 

GROUND 

(

GREEN

) wires together from 

fan to 

BARE

/

GREEN

 wire from ceiling with wire 

connector provided.

 
If you intend to control the fan light with a separate 
light switch, connect 

BLUE

 wire from fan to the 

BLACK

 (or 

RED

) supply from the independent 

switch. 

 
* Wrap each wire connector separately with 
electrical tape as an extra safety measure.

4. Hanging Bracket Installation.
(cont.)

5. Wiring.

hanging

bracket

spring washers

outlet box screws

flat washers

hanging

bracket

j-hook

motor assembly

*

WHITE

WHITE

BLACK

BLACK

BLUE

GREEN

GREEN

outlet box

GROUND 

(GREEN 

OR BARE)

supply circuit

WHITE

BLACK

SWITCH

Summary of Contents for RG52BNK5L











Reviews: