Lite-on Tech SOSC-2483KX User Manual Download Page 16

 

16 

ENGLISH

T

ROUBLESHOOTING

 

If you meet any trouble during installation or normal use of your COMBO drive, please refer 
to the following information. 

Read Problems 

Symptom Possible 

Causes 

Solutions 

No power. 

 

Check if the power cord is connected 

securely to the connector. 

No operation. 

USB cable isn't connected 
properly. 

 

Ensure that the USB cable and connectors 

are not damaged, bent or dented. Check 
especially the pins. 

Power is not switched on. 

 

Check if LED of your COMBO drive is 

lit.  If not, there is no power. 

USB cable is not connected 
properly between the 
computer USB port and 
COMBO drive. 

 

Ensure that both connectors of the USB 

cable is properly connected to the USB 
ports on the computer and the COMBO 
drive. 

No COMBO drive 
recognition. 

USB COMBO drive is not 
recognized by the Windows 
Operating System. 

 

Please refer to the USB 2.0 Users chapter 

and check if the USB driver is installed 
properly. 

Eccentric disc loaded. 

 

Replace it with another one. 

Excessive noise when 
reading. 

Seal attached on the surface

 

Detach the seal very carefully. Don't 

make any scratches. 

Eject locked by software. 

 

Stop the applying software and try the 

eject button to open the tray. 

Cannot open the tray 
(Eject). 

CD set incorrectly. 

 

Insert a small stick or paper clip into this 

hole to eject the tray. 

"Load Contents" or "Import 
Session" was NOT clicked 
on the Software. 

 

If recorded without checked "Load 

Contents" or "Import Session", it is 
impossible to read. But when using 
utility software such as "Session 
Selection" from Adaptec, the former 
session can be read. 

Defective disc. 

 

Deep scratches, fingerprints or other 

contaminants on the discs surface can 
disable the drive from reading data. 
Always keep it clean. 

Music CD inserted. 

 

Because audio compact discs do not have 

computer data, typing computer 
commands while an audio CD is in your 
drive will result in an error message. 

 

Cannot read the 
former session of 
the CD-RW disc 
which has been 
written at least 
twice. 

 

Read error 
occurs. 

Disc inserted upside down. 

 

Remove the disc from tray and reinsert it 

with the label side up. 

 

Summary of Contents for SOSC-2483KX



















Reviews: