manualshive.com logo in svg

Listen SoundConnect 2, User Manual

Share
Download
Listen SoundConnect 2 User Manual Download Page 27

SoundConnect 2

TM

 Manual

Service and Repair

21

Service and Repair

SoundConnect 2 is designed and constructed to provide the user with many years of safe and trouble free 
operation. However, should a fault occur which impairs its correct functioning, it should be immediately shut 
off, disconnected at the mains source and disconnected from other hardware. For repair, contact your local 
LISTEN service representative. Under no circumstances should persons not qualified in the service of 
electronic instrumentation attempt repair.

Contact Information

Contact the Listen office at 617-556-4104, Monday thru Friday, between 9 AM and 5 PM EST.

Sales - 

[email protected]

                  

Technical Support - 

[email protected]

580 Harrison Ave, Suite 3W • Boston, MA 02118 • 617-556-4104 • Fax 617-556-4145 • www.listeninc.com

© COPYRIGHT 2013-2020 LISTEN, INC. All rights reserved.

SoundCheck

®

, HarmonicTrak™, STWEEP™, SoundCheck ONE™, SoundMap™, NoiseCheck™, 

SoundConnect™, DC Connect™, AmpConnect™, AmpConnect ISC™, SC Amp™, SoundConnect 2™, 
AudioConnect™ and AudioConnect 4x4™ are trademarks of Listen, Inc.

REV 022820

Summary of Contents for SoundConnect 2




























Reviews:

No comments

Brands by name

Popular brands

Load more brands