9
574-537-8900
Rev: 10.23.19
JT’s Strong Arm
™
Installation and Owner’s Manual
(For Aftermarket Applications)
CCD-0001455
B.
Reassemble stabilizer tubes with the inner tube
sticking out past the end of the outer tube by 5”. Tighten
T-Bolts until snug
(Fig.6)
.
13.
To ensure proper installation, make sure the warning
labels are facing outward and right-side up. The T-Bolts
should be on the top side of the stabilizers.
A.
Apply a thin layer of white grease to swing bolt tabs.
B.
Attach clevis of outer stabilizer tube to the swing bolt
tab under center of chassis with a 3/8” - 16 x 1 1/2” bolt,
3/8” washer and 3/8” - 16 Nyloc
®
nut.
C.
Tighten nut until the stabilizer tubes swing to the
ground with resistance.
D.
Attach clevis of inner stabilizer tube to swing bolt tab
on jack leg with a 3/8” - 16 x 1 1/2” bolt, 3/8 washer and
3/8” - 16 Nyloc
®
nut. Loosen T-Bolt if needed.
E.
Repeat steps 13A-13D for opposite side of the chassis.
14.
Prepare stabilizer tube as described in step 12. To
ensure proper installation, make sure the warning labels
are facing outward and right-side up. The T-Bolts should
also be on the top side of the stabilizers.
A.
Apply a thin layer of white grease to swing bolt tabs.
B.
Attach clevis of outer stabilizer tube to the swing bolt
tab under main rail of chassis with a 3/8” - 16 x 1 1/2” bolt,
3/8” washer and 3/8” - 16 Nyloc
®
nut.
Fig.6
C.
Tighten nut until the stabilizer tubes swing to the
ground with resistance.
D.
Attach clevis of inner stabilizer tube to tab on electric
jack clevis with a 3/8” - 16 x 1 1/2” bolt, 3/8 washer and
3/8” - 16 Nyloc
®
nut. Loosen T-Bolt if needed.
E.
Repeat steps 14A-14D for opposite side of the chassis.
NOTE:
For chassis with rear scissor jacks, go to step 15.
For chassis with telescoping rear jacks, go to step 16.
15.
Starting with one of the rear scissor jacks, remove the
existing lower, outside pivot bolt. Replace pivot bolt with a
3/8” - 16 x 4” swing bolt.
A.
Install swing bolt from back-to-front with the shoulder
of the swing bolt to the rear side of the jack.
B.
Place 3/8” washer and a 3/8” - 16 Nyloc
®
nut
onto the threaded end of the swing bolt. Tighten nut
enough so that the swing bolt will only pivot by using a
screwdriver for leverage. Make sure the swing bolt tab is
positioned horizontally.
C.
Prepare T-Bolts and stabilizer tubes as described in
step 12, except the inner tube should be set at 1” instead
of 5”.
D.
After fully retracting rear scissor jacks, attach the clevis
end of the stabilizer inner tube to the swing bolt tab on the
rear side of the jack using a 3/8” - 16 x 1 1/2” bolt with a
3/8” washer on the top and bottom of the tab and a 3/8” -
16 Nyloc
®
nut. Tighten nut until tight.
E.
Repeat steps 15A-15D for opposite side of the chassis.
NOTE:
If scissor jacks are less than 2” wide, washers will
be necessary on the swing bolt because the threads may
not be long enough.
16.
Drill a 3/8” hole centered in the telescoping channel
and 1” up from the end.
A.
For 2006 or later telescoping jacks:
I.
Replace existing 3/8” jack pad bolt with 3/8” - 16 x 4”
swing bolt. Use 3/8” - 16 nut to secure swing bolt.
