background image

SYSTEM

WARNING

FAILURE TO ACT IN ACCORDANCE WITH THE FOLLOWING MAY

RESULT IN SERIOUS PERSONAL INJURY OR DEATH.

The 

Lippert Hydraulic Slideout System

 is intended for the sole

purpose of extending and retracting the slideout room.  Its

function should not be used for any other purpose or reason than

to actuate the slideout room.  To use the system for any reason

other than what it is designed for may result in damage to the

coach and/or cause serious injury or even death.

Before actuating the system, please keep these things in mind:

1.  Parking locations should be clear of obstructions that may

cause damage when the slideout room is actuated.

2.  Be sure all persons are clear of the coach prior to the

slideout room actuation.

3.  Keep hands and other body parts away from slideout

mechanisms during actuation.  Severe injury or death may

result.

4.  To optimize slideout actuation, park coach on solid and level

ground.

DESCRIPTION

The 

Lippert Hydraulic Slideout System

 is a rack & pinion guide system, utilizing a

hydraulic actuator to move the room assembly. The power unite drives the
cylinder rod in a forward and backward motion to drive the slide room in and out.
The 

Lippert Hydraulic Slideout System

 is designed to operate as a negative

ground system.

3

PRIOR TO OPERATION

Prior to operating the 

Lippert Hydraulic Slideout System

, follow these guidelines:

1.  Coach should be parked on the most level surface available.
2.  Leveling or stabilizing system should be actuated to ensure coach will not
     move during operation of Bed Lift System.
3.  Be sure battery is fully charged.
4.  Be sure to keep all persons and pets clear of Bed Lift System during
     operation.

Summary of Contents for HYDRAULIC SLIDEOUT SYSTEM














Reviews: