manualshive.com logo in svg

Lionel Overland Freight Express, Owner'S Manual

Share
Download
Lionel Overland Freight Express Owner'S Manual Download Page 29

29

Maintaining and servicing your locomotive

Lubricating your locomotive

H

elp your Lionel locomotive lead a long and productive life on your railroad by maintaining
it properly. To keep your locomotive lubricated, we recommend that you purchase a Lionel

Lubrication and Maintenance Kit (6-62927), available from your authorized Lionel dealer. 

When you find that the lubrication points illustrated in Figure 10 appear dry, lubricate your

locomotive after you have removed any accumulated dirt and dust. There are two basic rules to
keep in mind when you are lubricating your locomotive: use only a small amount of lubrication
and avoid getting grease or oil on your locomotive’s wheels, roller pick-ups, or the track.

Figure 10. Underside details and lubrication points

Front

Rear

Body screws

Body screws

located under

pilot

Body screws located

under pilot

Lubricate with

Lionel oil

sparingly

Lubricate

with Lionel

grease 

sparingly

Lubricate with

Lionel oil

sparingly

Lubricate with

Lionel grease 

sparingly

Volume control

knob

Summary of Contents for Overland Freight Express









































Reviews:

No comments

Brands by name

Popular brands

Load more brands