background image

Limited Warranty/Lionel Service

T

his Lionel product, including all mechanical and electrical components, moving parts, motors and
structural components, except for light bulbs, is warranted to the original consumer-purchaser, for 

one

year

against original defects in materials or workmanship when purchased through an authorized Lionel

merchant.

This warranty does NOT cover normal wear and tear, light bulbs, defects appearing in the course of

commercial use, or damage resulting from abuse or misuse of the product by the purchaser. Transfer of this
product by the original consumer-purchaser to another person voids this warranty. Modification of this
product voids this warranty.

Any warranted product which is defective in original materials or workmanship and is delivered by the

original consumer-purchaser to Lionel L.L.C. or an authorized Lionel L.L.C. Service Center, together with proof
of original purchase will, at the option of Lionel L.L.C., be repaired or replaced, without charge for parts or
labor. In the event the defective product cannot be repaired, and a replacement is not available, a refund of the
original purchase price will be granted. Any products on which warranty service is sought must be sent freight
or postage prepaid, as transportation and shipping charges are not covered by the warranty.

In no event shall Lionel L.L.C. be liable for incidental or consequential damages.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above

exclusion may not apply to you.

This limited warranty gives you specific legal rights, and you may have other rights which vary from state

to state. 

Instructions for Obtaining Service

If service for this Lionel L.L.C. product is required, bring the item, along with your dated sales receipt and

completed warranty information to the nearest Authorized Lionel Service Center. Your nearest Lionel Service
Center can be found by calling 1-800-4-Lionel, or by accessing our Website at www.lionel.com.

If you prefer to send your product back to Lionel L.L.C. for repair in Michigan, you must first call 

586-949-4100 or FAX 586-949-5429, or write to Customer Service, P.O. Box 748, New Baltimore, MI 
48047-0748, stating what the item is, when it was purchased and what seems to be the problem. You will be
sent a return authorization letter and label to ensure your merchandise will be properly handled upon receipt.

Once you have received your return authorization and label, make sure that the item is packed to prevent

damage during shipping and handling. We suggest that you use the product’s original packaging. This
shipment must be prepaid and we recommend that it be insured.

Please make sure you have followed all of the above instructions carefully before returning any

merchandise for service. You may choose to have your product repaired by one of our Authorized Lionel
Service Centers after its warranty has expired. A reasonable service fee will be charged.

Warranty Information

Please complete the information below and keep it, along with your dated sales receipt. You must present

this and your dated sales receipt when requesting warranty service.

Name ________________________________________________________________________

Address ______________________________________________________________________

Place of Purchase ________________________________________________________________

Date of Purchase ________________________________________________________________

Product Number ________________________________________________________________

Product Description ______________________________________________________________

©2003 L

IONEL

L.L.C., C

HESTERFIELD

, MI 48051-2493

U

NITED

S

TATES OF 

A

MERICA

P

RINTED IN 

C

HINA

Summary of Contents for 2343c F-3 A-A

























Reviews: