manualshive.com logo in svg

LinMot E1450-EC-QN-0S, Installation Manual

Share
Download
LinMot E1450-EC-QN-0S Installation Manual Download Page 21

                

E1400 V1 Rev. E Installation Guide   

  

 12 Ordering Information

Item

Description

Art. No.

E1450-PL-QN-0S

POWERLINK Drive (3x400/480VAC/28A)

0150-1791

E1450-PN-QN-0S

PROFINET Drive (3x400/480VAC/28A)

0150-1783

E1450-EC-QN-0S

ETHERCAT Drive (3x400/480VAC/28A)

0150-1784

E1450-SC-QN-0S

SERCOS III Drive (3x400/480VAC/28A)

0150-1785

E1450-IP-QN-0S

ETHERNET IP Drive (3x400/480VAC/28A)

0150-1782

E1450-SE-QN-0S

SERCOS over ETHERCAT Drive (3x400/480VAC/28A)

0150-1899

E1430-DP-QN-0S

PROFIBUS-DP Drive (3x400/480VAC/28A)

0150-1786

E1400-GP-QN-0S

GENERAL PURPOSE Drive (3x400/480VAC/28A)

0150-1779

E1450-PL-QN-1S

POWERLINK Drive (3x400/480VAC/28A/STO)

0150-2355

E1450-PN-QN-1S

PROFINET Drive (3x400/480VAC/28A/STO)

0150-2356

E1450-EC-QN-1S

ETHERCAT Drive (3x400/480VAC/28A/STO)

0150-2353

E1450-SC-QN-1S

SERCOS III Drive (3x400/480VAC/28A/STO)

0150-2357

E1450-IP-QN-1S

ETHERNET IP Drive (3x400/480VAC/28A/STO)

0150-2354

E1450-SE-QN-1S

SERCOS over ETHERCAT Drive (3x400/480VAC/28A/STO)

0150-2358

E1430-DP-QN-1S

PROFIBUS-DP Drive (3x400/480VAC/28A/STO)

0150-2352

E1400-GP-QN-1S

GENERAL PURPOSE Drive (3x400/480VAC/28A/STO)

0150-2351

Accessories

Description

Art. No.

Isolated USB-RS232 
converter

Isolated USB RS232 converter with config. cable

0150-2473

RS232 PC config. Cable 2.5m

For C1100/C1250/E1200/E1400/M8000

0150-2143

Isolated USB-serial converter

Isolated USB RS232/422/485 converter

0150-3120

RR01-68/100

Regeneration resistor (68R, 100W, 1000V) (X1 connector is included)

0150-3373

EV01-E1400

Fan Option for E1400 (X29 Fan connector is included)

0150-5055

NF01-FN258-16-07

3-phase line filter for E1400

0150-2359

DC01-E1400/X4/X30

Drive Connector Set for E1400-0S

0150-3452

DC01-E1400/X4/X30/X33

Drive Connector Set for E1400-1S

0150-3453

DC01-E1400/X1

Drive Connector Regeneration / Busbar

0150-3445

DC01-E1400/X2

Drive Connector Motor Phases

0150-3446

DC01-E1400/X4

Drive Connector 24VDC & Logic

0150-3447

DC01-E1400/X29

Drive Connector Fan

0150-3448

DC01-E1400/X30

Drive Connector Mains Supply (3x400/480VAC)

0150-3449

DC01-E1400/X31/X32

Drive Connector Brake

0150-3450

DC01-E1400/X33

Drive Connector Safety (-1S)

0150-3451

     

Bold items are strongly recommended accessories!

 

ATTENTION: The connectors have to be ordered separately and are not 
included with the drive! 

 

Use isolated USB RS232 converter for configuration!

 13 International Certifications

Certifications

Europe

See chapter “14 Declaration of Conformity CE-Marking“

UL

UL508C pending

NTI AG / LinMot

®

www.LinMot.com

Page 21/23

Summary of Contents for E1450-EC-QN-0S
























Reviews:

No comments

Brands by name

Popular brands

Load more brands