FIGURE1 Terminal Wiring with Security Alarm Panel
FIGURE2 Terminal Wiring with Fire Alarm Panel ( 3 Wires)
FIGURE3 Terminal Wiring with Fire Alarm Panel ( 4 Wires)
5. OPERATION AND TESTING
Check and test the gas alarm after installation. It should be
tested weekly and check after re-occupation following a
holiday.
After turn on the power, the LED is on, and then the unit
would take 30 to 300 seconds to warm up. In the warm up
time, the Yellow LED would flashes until end of the warm
up period.
Check that LED indication LED is on to ensure the power
supply is turn on.
Check that the LED flashes every 8 seconds to ensure the
unit is in operating mode.
Press and hold the test button for up to 1 to 3 seconds,
and the alarm should sound and the LED flash rapidly
while buzzer is sounding, after 6 seconds later, the alarm
exit the test mode and return to normal operating mode.
To ensure the gas alarm is working, you should test it
weekly.
While detecting the gas leaking, the Red Alarm LED would
turn on and the buzzer sound, and relay contacts would be
activated and output signals.
6. GAS SAFETY GUIDE
If you hear the gas alarm sound or suspect that
there is a gas leakage. You should open all
windows and doors to allow the gas to disperse.
FIGURE 4
FIGURE 5
Don’t switch on lighting, press door bell, exhausting
fan or any kind of electrical appliance to avoid
explosion.
FIGURE 6
FIGURE 7
Check all the gas appliances. Extinguish any naked
flames and turn off the gas control off the gas
supply.
Call the Fire department immediately outside your
home or premises/ apartment.
7. HOME SAFETY GUIDE
If you are on holiday, turn off appliances switches &
the gas control valve.
Do not place the bed near gas pipes or gas meter.
Do not change the location of gas pipes by yourself.
In order to ensure your home safety, please employ
registered installers for regular safety inspection of all
gas installation & appliances.
Attention:
Keep these things, such as paints, chemicals, alcohol
away to make a false alarm.
8. Service and Warranty.
Install and adjust according to this guide book.
Check the detector once a week; please keep
contact with the service provider immediately if you
get some problems.
Do not tear down or sling the detector randomly.
Do not use chemicals to clean the detector directly,
or wash with water.
The detector is designed with automatic detection, if
the gas sensor or unit in error, do not disassemble
the unit yourself, but get advice from professional
company or service provider.
The manufacturer guarantees to take the
responsibility for free repair and exchange for one
year from the date of purchase if there is quality
problem, and only charge for capital cost beyond
one year.
E
O
L R
esi
st
o
r(
6.
8K
)
ZONE+
DC24V-(0V)
C
o
nv
en
ti
o
n
al
F
ir
e
Al
arm
C
o
nt
ro
l
P
a
n
e
l
ZONE-
R
e
si
st
o
r
(4
70
oh
m
/1
w
)
R
e
si
st
or
(4
70
oh
m/1
w
)
Se
c
u
ri
ty
Al
ar
m
P
a
n
e
l
DC12V+
DC12V-
DC
Po
w
er
Su
pp
ly
is
U
npo
ar
iz
ed
w
ir
e
Alarm Signal
Re
la
y Ou
tp
ut
-C
OM
R
el
ay
Ou
tp
ut
-N
C/
NO
Alarm Signal
Re
la
y Ou
tp
ut
-C
OM
R
el
ay
Ou
tp
ut
-N
C/
NO
E
O
L R
e
si
st
o
r(
6.
8
K
)
DC24V+
DC24V-
C
o
nve
n
tion
a
l
Fir
e
A
larm
C
o
ntro
l
P
a
n
el
ZONE+
Resistor
(470 ohm/1w)
ZONE-
