➏
GD00Z-3 MOUNTING
➐
GD00Z-3 CONNECTIONS
➑
SYSTEM OPERATION
➒
OPERATION NOTES
1.
The
w
arning light
w
ill fl ash and the
w
arning
b
eeper
w
ill so
u
nd for fi
v
e seconds
b
efore the door opener is acti
v
ated.
STAY CLEAR OF THE DOOR, AND DOOR
OPENER. THEY ARE ABOUT TO MOVE!
2.
If the door does not completely open or close after remote acti
v
ation, the GD00Z-3
w
ill allo
w
u
ser to try to operate the door one more time. If the second attempt fails,
the GD00Z-3
w
ill go into lock-o
u
t mode. See Note #3.
3.
If the GD00Z-3 is in lock-o
u
t mode and
w
ill not accept remote commands, acti
v
ate
the door from the p
u
sh
bu
tton
w
all console.
4.
Once the GD00Z-3 has initiated the mo
v
ement of the garage door, another
command cannot
b
e sent for 30 seconds. This eliminates the chance of “
b
o
u
ncing”
the garage door and possi
b
ly damaging the garage door opener.
➓
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
Una
b
le to incl
u
de in
Z-
W
a
v
e net
w
ork.
GD00Z-3
w
as not
properly excl
u
ded
from a pre
v
io
u
s
Z-
W
a
v
e net
w
ork.
1. Reset the GD00Z-3
b
y pressing
the LINK
bu
tton 5 times. A
qu
ick
b
eep follo
w
ed
b
y a longer
b
eep
w
ill indicate the reset.
The GD00Z-3 does
not fl ash or
b
eep
w
hen acti
v
ated.
No po
w
er to the
GD00Z-3.
1. Make s
u
re the po
w
er s
u
pply is
pl
u
gged in sec
u
rely to a li
v
e o
u
tlet.
2. Make s
u
re the po
w
er cord
is pl
u
gged in sec
u
rely to the
GD00Z-3.
The GD00Z-3
fl ashes and
b
eeps
w
hen acti
v
ated
bu
t
the door does not
mo
v
e.
O
b
str
u
ction
b
locking the door
or incorrect
w
iring.
1. Make s
u
re that there are no o
b
stacles
pre
v
enting the door from mo
v
ing.
2. Make s
u
re that the GD00Z-3
connection
w
ires are connected
to the proper terminals on the
garage door opener. Trace the
w
ires from the garage door
opener’s p
u
sh
bu
tton
w
all console
to the door opener. This is
w
here
the GD00Z-3 connection
w
ires
sho
u
ld
b
e connected to.
Garage door opens
or closes,
bu
t the
stat
u
s does not
change on the
W
e
b
site or mo
b
ile app.
The tilt sensor
signal is not
b
eing
recei
v
ed
b
y the
GD00Z-3.
1. Make s
u
re the tilt sensor is
mo
u
nted correctly on the garage
door,
w
ith the arro
w
pointing
u
p.
2. Make s
u
re the
b
attery p
u
ll ta
b
has
b
een remo
v
ed from the tilt sensor.
3. Replace the
b
attery in the tilt sensor.
LIMITED RETAIL WARRANTY
Linear LLC (the Company)
w
arrants to the original p
u
rchaser that prod
u
cts deli
v
ered here
u
nder
w
ill
b
e free of
defects in materials and
w
orkmanship for a period of one (1) year from the date of p
u
rchase.
The Company
w
ithin said period shall at its option, either repair or replace free of charge, any prod
u
ct or part
thereof fo
u
nd,
u
pon the Company’s inspection, to
b
e so defecti
v
e, and
w
ill ret
u
rn the repaired or replaced prod
u
ct
to the p
u
rchaser at Company’s expense.
The GD00Z-3 is sold excl
u
si
v
ely thro
u
gh Nexia Home Intelligence. For
w
arranty ser
v
ice, contact Nexia C
u
stomer
Ser
v
ice at 877-288-7707.
This
w
arranty is conditioned on the follo
w
ing:
1. The Company m
u
st
b
e notifi ed
w
ithin one year of p
u
rchase and ha
v
e
b
een gi
v
en the opport
u
nity of
inspection
b
y ret
u
rn of any alleged defecti
v
e prod
u
ct free and clear of all liens and enc
u
m
b
rances to
the Company or its distri
bu
tor; and
2. The prod
u
ct m
u
st not ha
v
e
b
een a
bu
sed, mis
u
sed or improperly maintained and/or repaired d
u
ring
s
u
ch period; and
3. S
u
ch defect has not
b
een ca
u
sed
b
y corrosion or expos
u
re to other than ordinary
w
ear and tear.
THE COMPANY MAKES NO OTHER
W
ARRANTY OR REPRESENTATION OF ANY KIND
W
HATSOEVER
INCLUDING ANY
W
ARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE
HEREBY DISCLAIMED.
The Company’s maxim
u
m lia
b
ility here
u
nder is limited to the p
u
rchased price of the prod
u
ct. In no e
v
ent shall the
Company
b
e lia
b
le for any conse
qu
ential, indirect, incidental, or special damages of any nat
u
re arising from the
sale or
u
se of the prod
u
ct,
w
hether
b
ased in contract, tort, strict lia
b
ility or other
w
ise.
Note: Some states do not allo
w
limitations on incidental or conse
qu
ential damages or ho
w
long an implied
w
arranty lasts, so that the a
b
o
v
e limitations may not f
u
lly apply. This
w
arranty gi
v
es specifi c legal rights and yo
u
may also ha
v
e other rights
w
hich may
v
ary from state to state.
This de
v
ice complies
w
ith FCC Part 15 and Canada R
u
les and Reg
u
lations. Operation is s
ub
ject to the follo
w
ing
t
w
o conditions: (1) This de
v
ice may not ca
u
se harmf
u
l interference and (2) this de
v
ice m
u
st accept any interference
recei
v
ed, incl
u
ding interference that may ca
u
se
u
ndesired operation.
Le présent appareil est conforme a
u
x CNR d’Ind
u
strie Canada applica
b
les a
u
x appareils radio exempts de licence.
L’exploitation est a
u
torisée a
u
x de
u
x conditions s
u
i
v
antes : (1) l’appareil ne doit pas prod
u
ire de
b
ro
u
illage, et (2)
l’
u
tilisate
u
r de l’appareil doit accepter to
u
t
b
ro
u
illage radioélectri
qu
e s
ub
i, même si le
b
ro
u
illage est s
u
scepti
b
le
d’en compromettre le fonctionnement.
Changes or modifi cations not expressly appro
v
ed
b
y the man
u
fact
u
rer co
u
ld
v
oid the
u
ser’s a
u
thority to operate
the e
qu
ipment.
Les changements o
u
modifi cations non appro
uv
és expressément par la partie responsa
b
le de la conformité
po
u
rrait ann
u
ler l’a
u
torité de l’
u
tilisate
u
r à faire fonctionner l’é
qu
ipement.
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,GD00Z-3 - LINEAR P/N: 236386 X10 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 2 OF 2
The GD00Z-3 typically
mounts on the ceiling
near the opener and
the power outlet
Tilt sensor
mounted on
the top panel
of the door
THE GD00Z-3 CAN ALSO BE ATTACHED TO THE OPENER'S
HARDWARE USING THE ADJUSTABLE MOUNTING BRACKET
THE GD00Z-3 WARNING
LAMP MUST BE VISIBLE IN
ALL DOOR POSITIONS
3/16" HOLES
FOR A
N
CHORS
The optional adjustable
mounting bracket fits
3 ways on the GD00Z-3
The bracket snaps onto
indents on either side or
on the end of the GD00Z-3
Secure
bracket
with screw
Use the four screws
and anchors to mount
the GD00Z-3 above
the opener
I
N
DE
N
T
I
N
DE
N
T
Use the bolts and nuts supplied
to attach the bracket to a secure
structure
BE SURE THE GD00Z-3
IS CLEAR OF ALL MOVING
PARTS OF THE GARAGE DOOR
AND THE WARNING LAMP IS
NOT OBSTRUCTED
I
N
DE
N
T
1A
2A
REMOVE POWER FROM THE
GARAGE DOOR OPENER
BEFORE CONTINUING
! WARNING !
1
PUSHBUTTON
PUSHBUTTON
GARAGE
DOOR
OPENER
Connect the GD00Z-3 connection
wires to the pushbutton wall console
terminals on the garage door opener.
The terminals may be named "PWC", "WC",
"PB", "PUSHBUTTO
N
", or "RED and WHITE".
Terminal names and locations vary by model.
DO NOT DISCONNECT
ANY WIRES CURRENTLY
CONNECTED TO THE
GARAGE DOOR OPENER !!!
Remove the screw from 120
V
AC
outlet faceplate. Secure the retaining
bracket to the faceplate with the provided
screw. Snap the power supply into the
bracket while plugging into the outlet.
USE WIRE TIES TO SECURE
EXCESS WIRING CLEAR
OF ALL MOVING PARTS
OF THE GARAGE
DOOR AND OPENER
Either wire can
connect to either
terminal
Plug the power cord
into the power input
jack on the GD00Z-3
2
1
3
FLASH
FLASH
FLASH
BEEP
BEEP
BEEP
Use the
N
exia portal or
mobile app to control
your garage door
The GD00Z-3 will activate
the door opener and open
or close the door
STAY CLEAR
OF THE DOOR !!!
3
The GD00Z-3 will beep and
flash for five seconds before
the door moves
4
5
6
The Web page or mobile
app will show the new status
of the door after the door
completes its cycle
Restore power to your
garage door opener
1
To synchronize the system,
use the garage door opener's
pushbutton to manually open
and close the door
2
STAY CLEAR
OF THE DOOR !!!
Use
N
exia to add your garage door control
to Automations and Modes. For example:
Schedule your garage door to close at
sunset. See HELP at mynexia.com
for more details.
Copyright © 2014 Linear LLC
236386 X10
GD00Z-3
Specifi cations
Power
Supply:
Inp
u
t: 120 VAC, 0.8 A
O
u
tp
u
t: 12 VDC, 2 A
Operatin
g
Temperature:
-4º—122° F (-20º—50° C)
Audible
Alarm:
45 d
b
@ 10 feet
Strobe:
360 L
u
mens
Communications:
Z-
W
a
v
e (908.4 MHz)
Mountin
g
:
Scre
w
s and anchors to
the ceiling, or
b
racket to the
opener’s hanging hard
w
are
Tilt Sensor Specifi cations
Power
Supply:
Type CR2032 Coin Cell Battery
Operatin
g
Temperature:
-4º—122° F (-20º—50° C)
Battery
Life:
24 Months (typical)
Communications:
Proprietary 345 MHz
Ran
g
e:
100” line-of-sight to GD00Z-3
Mountin
g
to Gara
g
e Door:
Do
ub
le-sided tape or t
w
o
mo
u
nting scre
w
s
(Specifi cations s
ub
ject to change
w
itho
u
t notice)
NOTICE TO USERS IN CALIFORNIA - CR COIN
CELL LITHIUM BATTERY INFORMATION: THIS
PRODUCT CONTAINS A CR COIN CELL LITHIUM
BATTERY WHICH CONTAINS PERCHLORATE
MATERIAL - SPECIAL HANDLING MAY APPLY - SEE
www.dtsc.ca.
g
ov/hazardouswaste/perchlorate
KEEP AWAY FROM SMALL CHILDREN. IF BATTERY
IS SWALLOWED, PROMPTLY SEE A DOCTOR. DO
NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL
OF USED BATTERIES MUST BE MADE IN
ACCORDANCE WITH THE WASTE RECOVERY AND
RECYCLING REGULATIONS IN YOUR AREA.
