GD00Z-3
GARAGE DOOR OPENER
REMOTE COMMAND
TRANSCEIVER
with TILT SENSOR
Installation Instructions
➊
PRODUCT DESCRIPTION
➋
SAFETY NOTES
➌
PRODUCT COMPONENTS
➍
TILT SENSOR INSTALLATION AND BATTERY
➎
INCLUDING (ADD) WITH THE SYSTEM
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,GD00Z-3 - LINEAR P/N: 236386 X10 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 1 OF 2
WARNING
This operator system is equipped with an unattended
operation feature. This door could move unexpectedly.
NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR!
WARNING
This system can be installed on sectional type (roll up) doors
only per (UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!
WARNING
Do not install the Remote Command Transceiver on
garage door operators manufactured prior to 1993
(models without an operational safety beam entrapment
detection system).
WARNING
The Remote Command Transceiver must be mounted in
the garage, in sight of the garage door, where the visual
and audible movement warning indicators can be clearly
seen and heard.
GD00Z-3
POWER
I
N
PUT
JACK
WAR
N
I
N
G
LIGHT
LI
N
K
BUTTO
N
CO
NN
ECTIO
N
WIRES
MOU
N
TI
N
G SCREWS
A
N
D A
N
CHORS
FOR GD00Z-3
POWER
SUPPLY
TILT
SENSOR
STATUS
I
N
DICATOR
OPTIONAL
ADJUSTABLE
GD00Z-3 MOUNTING
BRACKET
POWER
SUPPLY
RETAINING
BRACKET
SCREWS A
N
D
MOU
N
TI
N
G TAPE
FOR TILT SE
N
SOR
SCREW A
N
D
MOU
N
TI
N
G HARDWARE
FOR ADJUSTABLE
BRACKET
SCREW FOR
POWER SUPPLY
BRACKET
WIRE
TIES
TO INCLUDE THE
GD00Z-3 INTO NEXIA
TO EXCLUDE THE
GD00Z-3 FROM NEXIA
1
2
1
2
Start the exclusion process
on your controller:
●
N
exia bridge: Press (-) button
WALL
OUTLET
POWER
SUPPLY
POWER
I
N
PUT
JACK
LI
N
K
BUTTO
N
GD00Z-3
In
N
exia, click "Security & Sensors".
Click Add Device. Click Security.
Click Enroll for the Garage Door
Control.
Press the link button
on the GD00Z-3
Note: Plug in the GD00Z-3
near your Nexia bridge or
controller for these steps
Login to your account at:
www.mynexia.com
●
Thermostat with bridge:
press menu,
N
exia, exclude device
(Only do this to remove the garage door
control from your network)
3
When instructed, tap and release
the Link button on the GD00Z-3
CR2032
PLUS SIDE UP !!!
The system will notify you
when the battery is low,
replace the battery with
a type CR2032 coin cell
Insert the
battery
into the
transmitter
To open the case, twist
a small screwdriver
in case slot
SLOT
Use double sided tape or
the two mounting screws supplied
(drill 1/16" pilot holes if required)
POST O
N
BOTTOM
"UP"
ARROWS
Snap the sensor onto
the mounting plate
To activate the tilt sensor,
remove the battery protection pull strip
2
ARROWS ON PLATE
& SENSOR POINT UP
LOW BATTERY REPLACEMENT
1
2
1
3
Attach the mounting plate
to the
top panel
of the door
GD00Z-3 Overview
• A garage door opener remote
command transcei
v
er
w
ith
bu
ilt-in
Z-
W
a
v
e technology.
• Allo
w
s remote operation of a garage
door opener
u
sing the Nexia Home
Intelligence
w
e
b
portal or mo
b
ile app.
• Acts as a Z-
W
a
v
e repeater to impro
v
e
comm
u
nications
w
ithin the Z-
W
a
v
e
mesh net
w
ork.
GD00Z-3 Summary of Operation
• GD00Z-3 connects to the garage door
opener’s p
u
sh
bu
tton
w
all console
terminals.
• A
w
ireless tilt sensor mo
u
nts on the
garage door and reports the door’s
position to the GD00Z-3.
• GD00Z-3 responds to Z-
W
a
v
e
commands from Nexia to open or close
the garage door.
• A
w
arning indicator light fl ashes and
a
b
eeper so
u
nds for 5 seconds
b
efore
the door
b
egins to mo
v
e.
• If the door does not completely
open or close, a second open or
close command can
b
e sent after
30 seconds.
• If the door does not completely open
or close after the second attempt,
the GD00Z-3 operation is s
u
spended
u
ntil a local garage door p
u
sh
bu
tton is
acti
v
ated.
Z-Wave Information
• Z-
W
a
v
e® is a registered trademark
of Sigma Designs Inc. and/or its
s
ub
sidiaries.
• Z-
W
a
v
e is an Interopera
b
le t
w
o-
w
ay RF
mesh net
w
orking technology designed
for
u
se
w
ith a Z-
W
a
v
e gate
w
ay/
controller and other Z-
W
a
v
e ena
b
led
de
v
ices.
• Replication is the process of copying or
transferring yo
u
r Z-
W
a
v
e net
w
ork from
one controller to another.
• This is a Sec
u
rity ena
b
led Z-
W
a
v
e
prod
u
ct and m
u
st
b
e
u
sed
w
ith a
Sec
u
rity ena
b
led Z-
W
a
v
e controller
in order to f
u
lly
u
tilize this prod
u
ct. As
s
u
ch, this de
v
ice
w
ill not respond to
Basic CC commands.
• ASSOCIATION: The GD00Z-3 s
u
pports
1 Gro
u
p
w
ith 1 Node. Gro
u
p 1 m
u
st
b
e
assigned the Node ID of the controller
to
w
hich
u
nsolicited notifi cations from
the GD00Z-3
w
ill
b
e sent. The Nexia
Bridge sho
u
ld set this association
a
u
tomatically after incl
u
sion.
Nexia Customer Service:
(877) 288-7707 (USA & Canada)
