INSTR,INSTL,DXS-32
LINEAR P/N: 216314 B
MATERIAL: 20 LB. MEAD BOND
SIZE: 8.500" X 11.000"
INK: BLACK
SCALE: 1-1
SIDE 2 OF 2
EXAMPLE INSTALLATIONS
TRANSMITTER MOUNTING
ADJUSTING MAGNET HEIGHT
PROGRAMMING RECEIVER
CHANGING BATTERIES
LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and workmanship for twelve (12) months. The Warranty
Expiration Date is labeled on the product.
This warranty extends only to wholesale customers
who buy direct
from Linear or through Linear’s normal distribution channels.
Linear does not warrant this product to
consumers.
Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any.
There are no obligations or liabilities on the part of Linear corporation for consequential damages arising out
of or in connection with use or performance of this product or other indirect damages with respect to loss of
property, revenue, or profit, or cost of removal, installation, or reinstallation.
All implied warranties, including
implied warranties for merchantability and implied warranties for fitness, are valid only until Warranty Expiration Date
as labeled on the product.
This Linear Corporation Warranty is in lieu of all other warranties express or implied.
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear
Technical Services at 1-800-421-1587 for an RPA# and other important details.
FCC NOTE:
This device complies with FCC Part 15 and IC Canada Rules and Regulations. Operation is subject the following
two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fill an important need in portable wireless
signalling. However, there are some limitations which must be observed.
✶
For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15
devices. As such, they have limited transmitter power and therefore limited range.
✶
A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio
signals that occur on or near their operating frequencies, regardless of code settings.
✶
Changes or modifications to the device may void FCC compliance.
✶
Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
✶
A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or
dealer, and these facts should be communicated to the ultimate users.
Copyright © 2000 Linear Corporation
216314 B
TRANSMITTER
MOUNTED ON
DOOR JAMB
(NOTE: SMALL END
OF TRANSMITTER UP)
(NOTE: SMALL END
OF TRANSMITTER DOWN)
MAGNET
MOUNTED
ON DOOR
MAGNET MOUNTED
ON DOOR
TRANSMITTER
MOUNTED ON
WINDOW SILL
MAGNET MOUNTED
ON WINDOW FRAME
SLIDING WINDOW
LEFT OPENING DOOR
RIGHT OPENING DOOR
TRANSMITTER
MOUNTED ON
DOOR JAMB
TRANSMITTER
MOUNTED ON
WINDOW FRAME
MAGNET
MOUNTED
ON WINDOW
SASH STILE
DOUBLE-HUNG WINDOW
ATTACH BOTTOM CASE
USING THE SCREWS OR
DOUBLE-STICK TAPE PROVIDED
NOTE: ATTACHING THE TRANSMITTER WITH DOUBLE-STICK
TAPE IS NOT ALLOWED IN UL INSTALLATIONS
ADJUST MAGNET
HEIGHT UNTIL
CASE LEVELS
ARE ABOUT EQUAL
TRANSMITTER
MAGNET
THE SNAP-ON MAGNET SPACER
CAN BE USED TO ADD 1/4" HEIGHT
TO THE MAGNET (SPACERS CAN ALSO
BE SNAPPED TOGETHER FOR MORE LIFT)
PROGRAMMING:
1. PLACE RECEIVER INTO PROGRAM
OR "LEARNING" MODE
2. ACTIVATE TRANSMITTER BY
OPENING DOOR OR WINDOW
3. VERIFY THAT THE RECEIVER
ACCEPTED THE SIGNAL
TESTING:
1. PLACE RECEIVER INTO TEST MODE
2. OPEN DOOR, VERIFY THAT THE
RECEIVER INDICATES AN OPEN DOOR
3. CLOSE DOOR, VERIFY THAT THE
RECEIVER RECOGNIZED THAT THE
DOOR IS CLOSED
OPEN
DOOR
1
SLIDE OLD BATTERIES
OUT OF BATTERY
HOLDERS
2
3
4
DISCARD OLD
BATTERIES
PROPERLY
INSERT TWO DURACELL DL2032
BATTERIES
PLUS (+) SIDE UP
INTO BATTERY HOLDERS
SEAT BATTERIES COMPLETELY
INTO HOLDERS
BE SURE BATTERIES ARE
NOT TOUCHING EACH
OTHER
