background image

5

PROGRAMMING OPTIONS

There are several AK-31 programming options. For most 
installations, the factory set default options are suffi cient. The 
keypad must be in Programming Mode to make these changes.

Select Door Sense or Inhibit Input 

Default: Door Sense

The input (gray wire) can be programmed for 

DOOR SENSE

 or 

INHIBIT

.

Press:

  

1 0 #

 

Input 

#

Input

 = 0 for Door 

S

ense, = 1 for Inhibit

When programmed for 

DOOR SENSE

, if an open condition on the input occurs 

before access is granted (with an entry code or with the request-to-enter input) a 

FORCED ENTRY

 output will occur. If an open condition remains 60 seconds after 

a relay activation for access, a 

DOOR AJAR

 output will occur.

When programmed for 

INHIBIT

, a closed condition on the input will prevent 

Relay #1 from activating when access is requested with an entry code. This mode 
is typically used with an external timer to disable the access device at certain 
times.

Select Forced Entry Output 

Default: Output #3

Sets which output activates if the 

DOOR SENSE

 input opens before access is 

granted. This output is not timed.

Press:

  

1 1 #

 

Output

 

#

Output

 = Output to Activate (0-4)

1 = Main Relay  2 = Auxiliary Relay  

3

 = Output #

3

  4 = Output #4  0 = No Output

Select Door Ajar Output 

Default: Output #4

Sets which output activates if the 

DOOR SENSE

 input stays open 60 seconds 

after access is granted. This output is not timed.

Press:

  

1 2 #

 

Output

 

#

Output

 = Output to Activate (0-4)

1 = Main Relay,  2 = Auxiliary Relay,  

3

 = Output #

3

,  4 = Output #4,  0 = No Output

Select Keypad Lockout Output 

Default: No Output

Sets which output activates when the keypad is “locked out” after too many 
incorrect entry code attempts. The lockout time is 60 seconds.

Press:

  

3

 #

 

Output

 

#

Output

 = Output to Activate (0-4)

1 = Main Relay,  2 = Auxiliary Relay,  

3

 = Output #

3

,  4 = Output #4,  0 = No Output

Select Keypad Active Output 

Default: No Output

Sets which output activates when any keys are pressed. This output is timed. If 
toggle mode is selected for the output, the timer value defaults to 2 seconds.

Press:

  

1 4 #

 

Output

 

#

Output

 = Output to Activate (0-4)

1 = Main Relay,  2 = Auxiliary Relay,  

3

 = Output #

3

,  4 = Output #4,  0 = No Output

Select Alarm Shunt Output 

Default: No Output

Sets which output activates during the time access is granted. (Use this output 
to shunt alarm contacts attached to the access door.) This output may be timed 
or toggled.

Press:

  

1 5 #

 

Output

 

#

Output

 = Output to Activate (0-4)

1 = Main Relay,  2 = Auxiliary Relay,  

3

 = Output #

3

,  4 = Output #4,  0 = No Output

Select Request-to-Exit Output 

Default: Main Relay

Sets which output activates when the Request-to-Exit input is grounded. This 
output may be timed or toggled.

Press:

  

1 6 #

 

Output

 

#

Output

 = Output to Activate (0-4)

1 = Main Relay,  2 = Auxiliary Relay,  

3

 = Output #

3

,  4 = Output #4,  0 = No Output

Main Relay On-time 

Default: 2 Seconds

Sets the length of time the Main Relay activates when triggered.

Press:

  

2 1 #

 

Seconds

 

#

Seconds

 = Output time in seconds (0-60)

Auxiliary Relay On-time 

Default: 2 Seconds

Sets the length of time Auxiliary Relay activates when triggered.

Press:

  

2 2 #

 

Seconds

 

#

Seconds

 = Output time in seconds (0-60)

Solid-state Output #3 On-time 

Default: 2 Seconds

Sets the length of time Output #3 activates when triggered.

Press:

  

3

 #

 

Seconds

 

#

Seconds

 = Output time in seconds (0-60), 99 = Toggle Mode

Solid-state Output #4 On-time 

Default: 2 Seconds

Sets the length of time Output #4 activates when triggered.

Press:

  

2 4 #

 

Seconds

 

#

Seconds

 = Output time in seconds (0-60), 99 = Toggle Mode

Beep Sounds on Keystrokes 

Default: Yes

Selects whether or not the keypad beeps as each key is pressed.

Press:

  

4 0 #

 

Sound

 

#

Sound

 = 1 for Yes, = 0 for No

Beep Sounds During Main Relay 

Default: No

Selects whether or not the keypad beeps during Main Relay activation.

Press:

  

4 1 #

 

Sound

 

#

Sound

 = 1 for Yes, = 0 for No

Beep Sounds During Auxiliary Relay 

Default: No

Selects whether or not the keypad beeps during Auxiliary Relay activation.

Press:

  

4 2 #

 

Sound

 

#

Sound

 = 1 for Yes, = 0 for No

Beep Sounds During Output #3 

Default: No

Selects whether or not the keypad beeps during Output #3 activation.

Press:

  

3

 #

 

Sound

 

#

Sound

 = 1 for Yes, = 0 for No

Beep Sounds During Output #4 

Default: No

Selects whether or not the keypad beeps during Output #4 activation.

Press:

  

4 4 #

 

Sound

 

#

Sound

 = 1 for Yes, = 0 for No

228037 A    IMAGE 7

Summary of Contents for AK-31









Reviews: