Linea Rotobomba 500T0800 Owner'S Manual Download Page 5

Electrical / Operation

5

To change or check tank pre-charge pressure:
1. Turn off power to the pump.
2. Close the suction line valve from the storage tank.
3. Open a faucet to drain pressure from the tank.
4. Use an air pressure gauge (same as used on automo-

bile tires), and check the air pressure from the air fit-
ting on top of the tank.

The tank pre-charge pressure should always be 0.138 Bar
(2 PSI) 

less than the cut-in (start) pressure (see Table I,

Page 4).

Changing Pressure Switch Settings 

The pressure switch is pre-set to 2 / 3.4 Bar (30 / 50 PSI).
The pressure cut-off (pump-stop pressure) can be
changed if required. 
To change cut-off (pump stop) and cut-on (pump start)
pressure together:
1. Turn off power to the pump.
2. Remove the cover to the pressure switch.

3. Turn pressure-adjustor #1 clockwise to increase both

cut-off and cut-in pressure. Each turn will change the
pressure setting 0.17 Bar (2.5 PSI). Turn the adjustor
counterclockwise to lower the pressure setting.

4. To raise only the cut-off pressure, turn pressure adjus-

tor #2 clockwise. Each turn will change the pressure
setting 0.17 Bar (2.5 PSI). Turn the adjustor counter-
clockwise to lower the pressure setting.

Checking Pressure Adjustment

1. After changing the pressure setting, put the cover on

the pressure switch.

2. Apply power. 
3. If the pump does not start up, open a faucet to drain

water from the pressure tank. 

4. Watch the pressure gauge and note at what pressure

the pump starts. 

5. Close the faucet.
6. Watch the pressure gauge and note at what pressure

the pump stops.

7. If additional adjustments need to be made, refer to

the previous procedure.

PRIMING / OPERATION

Never run pump dry

. Running pump with-

out water may cause it to overheat, damaging the seal
and possibly causing burns to persons handling the
pump. Fill the pump with water before starting.

Never run the pump with the discharge

closed. To do so can boil water inside the pump, causing
hazardous pressure in the unit, risk of explosion, and
possibly scalding persons handling the pump.

Cistern Installation

1. Remove the priming plug from the priming port. Fill

the pump from the tee and let it vent through the
port. Fill all piping between the pump and the water
source and make sure that all vertical suction piping
is full. 

2. Replace all priming plugs (use teflon tape). 
3.

Power on!

Start the pump. If you don’t have water in

2 minutes, stop the pump and remove the fill plugs.
Refill the pump and piping. You may have to repeat
this several times in order to remove all the trapped
air from the piping. A pump lifting water 15’ (4.5m)
may take as long as 15 minutes to prime.

Attach Po

w

er

W

ires Here

Press

u

re

Adj

u

stor #1

Press

u

re

Adj

u

stor #2

Attach Gro

u

nd

W

ire Here

Figure 4 – Pressure Switch.

Priming 
Tee

Figure 5 – Prime the Pump.

Summary of Contents for Rotobomba 500T0800





















Reviews: