Lindy 38143 User Manual Download Page 7

User Manual 

 

English

 

 

Operation 

EDID 

The Matrix is capable of using either preset or cloned EDID 
data to ensure maximum compatibility. The table shows the 
different  EDID  values  which  can  be  set  using  the  Matrix’s 
front  panel  buttons  or  using  the  supplied  software  via  RS-
232 or TCP/IP. 
 
Using the buttons on the front of the Matrix, press Menu to 
enter  the  EDID  Management  Window.  Press  Up  or  Down 
until you get to the EDID value which you want to set and 
then press Enter. Now use Up or Down to scroll to the Input 
you want to apply the EDID to and then press Enter again. 
 

 

 

IR Control 

The Matrix supports bi-directional IR signal extension, allowing control of the HDMI sources remotely from 
the Receiver and displays remotely from the Matrix, simply install the supplied IR Receivers and Emitters 
according to your requirement. 

Each of the IR TX ports (1 

– 4) located on the back of the Matrix unit is allocated to the corresponding 

HDMI  Input  (1 

–  4),  this  allows  you  to  control  whichever  HDMI  source  you  are  viewing  from  a  remote 

location even after switching between inputs. 

Each of the IR RX ports (1 

– 4) located on the back of the Matrix unit is allocated to the corresponding 

HDMI Input (1 

– 4), this allows you to control the HDMI display(s) currently using this Input. 

Please Note: Misplaced or poorly secured IR Emitters and Receivers may result in intermittent IR control 
signals passed to and from the matrix. Check your placement and adjust if necessary. 

 

 

PC Controller 

The Matrix can be controlled by a Windows PC connected via RS-232 (9 Way) cable or via a LAN using 
TCP/IP.  

Begin by connecting the PC and Matrix by your preferred method and then switch the Matrix on.  

Download  the  latest  version  of  MatrixController.exe  from  www.lindy.com  and  then  open  it  by  double 
clicking on it.

 

When you open the software you will be presented with the screens shown on the following page, you 
can now begin to configure the Matrix according to your requirement. 

 

 

 

 

EDID Mode 

EDID Description 

1080i, 2CH AUDIO 

1080i, DOLBY/DTS 5.1 

1080i, HD AUDIO 

1080p, 2CH AUDIO 

1080p, DOLBY/DTS 5.1 

1080p, HD AUDIO 

3D,1080p, 2CH AUDIO 

3D, 1080p,DOLBY/DTS 5.1 

3D,1080p, HD AUDIO 

10 

4k*2k, 2CH AUDIO 

11 

4k*2k, DOLBY/DTS 5.1 

12 

4k*2k, HD AUDIO 

13 

DVI 1024x768 

14 

DVI 1920X1080 

15 

DVI 1920X1200 

16 

Copy from HDMI OUTPUT A 

17 

Copy from HDMI OUTPUT B 

18 

Copy from HDMI OUTPUT C 

19 

Copy from HDMI OUTPUT D 

Summary of Contents for 38143

































Reviews: