background image

P/N 1604010 Rev D (ECN 35207) 

1-1 

Multi-Control Operation Manual

 

 

Section 1- Specifications and Compliance

Section 1- Specifications and Compliance

Requirements for Electrical Service

All electrical equipment shall be installed by a qualified electrician. As a result, a correct installation will allow the 

irrigation system to protect itself from overloads and ground faults with minimal downtime, or possible damage and 

hazards.

Refer to ANSI, ASAE Standard S397.2 (latest revision) Electrical Service and Equipment for Irrigation for exact 

requirements.

Compliance Standards

Federal Communications Commission (FCC) Statement

NOTE:

 This equipment has been tested and found to comply within the limits for a Class B digital device pursuant 

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-

ence when the equipment is operated in a commercial environment. This equipment generates, uses and radiates 

radio frequency energy and, if not used in accordance with the manufacturer’s instruction manual, may cause 

harmful interference with radio communications. 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.  This device may not cause harmful interference.

2.  This device must accept any interference received, including interference that may cause undesired operation.

These limits are designed to provide reasonable protection against harmful interference. However, there is no 

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfer-

ence with radio or television reception, which can be determined by turning the equipment on and off, try  to cor-

rect the interference by one or more of the following measures:

•  Reorient or relocate the antenna of the radio/television receiver.

•  Increase the separation between this equipment and the radio/television receiver.

•  Plug the equipment into a different outlet so that the equipment and the radio/television receiver are on different 

power main branch circuits.

•  Consult a representative of Lindsay Corporation for additional suggestions.

Industry Canada Compliance Statement

This Class B digital apparatus meets the requirements of the Canadian Interference-Causing Equipment Regula-

tions.

Cet appareil numerique de la Classe B respecte toutes les exigences du Relement sur le Materiel Brouilleur du 

Canada.

WEEE Statement

Lindsay Manufacturing, LLC products: D012-007-20 MC Panel; D012-007-11 MC Panel, 2.4 GHz; D012-007-14 

MC Expansion Panel; D012-007-22 WS Panel and D012-007-13 WS Panel, 2.4 GHz are sold and distributed in 

the European Union only by:

Lindsay Europe SAS

L’Epinglerie

72 300 La Chapelle d’Aligne

France

Phone: 33 (0)2 43480205

Summary of Contents for GrowSmart Multi-Control





























Reviews: