background image

Mini-

Mite™ Tube  Furnace

Warranty

22 

12  Warranty 

12.1  Domestic Warranty  {United  States  and 

Canada) 

Lindberg/Blue M warrants  this product to the owner for  a 

period of twelve  (12)  months  from  date of shipment  by 

Lindberg/Blue M. Under  this warranty Lindberg/Blue  M through 

its authorized  Dealer  or service  organizations,  will repair  or at 

its option  replace  any  part found  to contain  a manufacturing 

defect in material  or workmanship, without  charge to the owner, 

for a period of ninety  (90)  days, the labor, and a period of one 

(1) year, the parts,  necessary to remedy  any such defect.  All 

components used in the manufacture of this product  are 

covered  by this warranty  excluding heating  elements  and 

thermocouples. 
This  warranty  is limited  to products  purchased  and installed  in 

the United  States  and Canada. It does not apply to damage 

caused from  failure  to properly  install,  operate,  or maintain  the 

product in  accordance  with  the printed  instructions provided. 

This warranty  shall  not apply  to equipment  or parts  which have 

been subjected to negligence, accident,  or damage  by 

circumstances beyond  Lindberg/Blue M's  control  or improper 

operation, application, maintenance, or storage. 

To obtain  prompt  warranty  service,  contact  the nearest 

Lindberg/Blue M authorized  service center or Dealer. A listing of 

these companies will be provided  upon request.  Lindberg/Blue 

M's  own shipping records  showing  date of shipment  shall be 

conclusive  in establishing the warranty  period. 
This  warranty  is in lieu of any other  warranties,  expressed  or 

implied,  including merchantability or fitness  for a particular 

purpose. The  owner  agrees  that Lindberg/Blue  M's  sole liability 

with respect  to defective parts shall be as set forth in this 

warranty, and any claims  for incidental  or consequential 

damages are expressly  excluded. 

12.2  International Warranty {excluding Canada)  

12 Months Parts Warranty 

Lindberg/Blue M warrants this product to the original owner for 

a period of twelve (12) months from the date of shipment from 

the Lindberg/Blue M factory. Thermocouples and heating 

elements are excluded from this warranty. If any part is found 

to contain a manufacturing defect in material or workmanship 

Lindberg/Blue M will, at its option, repair or replace the part. 

Lindberg/Blue M assumes no responsibility for any labor 

expenses for service, removal, or reinstallation required to 

repair or replace the part, or for incidental repairs and such 

costs are the responsibility of the Owner and his Dealer. 

The warranty does not apply to damage caused by accidents, 

misuse, fire, flood, Acts of God or any other events beyond 

Lindberg/Blue M’s control or to damage caused from failure to 

properly install, operate, or maintain the product in accordance 

with the printed instructions provided by Lindberg/Blue M. To 

obtain prompt warranty service, simply contact the Dealer from 

whom you purchased the product or the nearest Dealer 

handling Lindberg/Blue M products. Lindberg/Blue M's own 

shipping records showing date of shipment shall be conclusive 

in establishing the warranty period. 

This warranty is in lieu of any other warranties, exp1essed or 

implied, including merchantability or fitness for a particular 

purpose. The owner agrees that its sole remedy and 

Lindberg/Blue M's sole liability with respect to defective parts 

or any other claim shall be as set forth in this warranty, and 

any claims for incidental, consequential or other damages are 

expressly excluded. 

Summary of Contents for Mini-Mite TF550 A


































Reviews: