Carrier PG95ESU User Manual Download

Page: 1 / 58

Installation, Start-up, Operating and Service Maintenance

Instructions

NOTE:

Read the entire instruction manual before starting the

installation
Approved for installations up to 5,400 feet (1646 meters)
TABLE OF CONTENTS

REQUIRED NOTICE FOR MASSACHUSETTS INSTALLATIONS

IMPORTANT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Table 1 – Minimum Clearances to Combustible Materials for All Units

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Table 2 – Loose Parts Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

CODES AND STANDARDS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS PROCE

DURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

AIR FOR COMBUSTION AND VENTILATION . . . . . . . . . . . . . . 8

Table 3 – Minimum Free Area Required for Each Combustion Air

Opening or Duct to Outdoors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Table 4 – Minimum Space Volumes for 100% Combustion, Ventila

tion and Dilution Air from Outdoors . . . . . . . . . . . . . . . . . . . . . . 10

CONDENSATE TRAP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

CONDENSATE DRAIN CONNECTION . . . . . . . . . . . . . . . . . . . . 11

Table 5 – Condensate Trap Configurations . . . . . . . . . . . . . . . . . 12

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Table 6 – Evaporator Coil Spacer or Shield Requirements. . . . . 16

Table 7 – Air Filter Selection and Duct Sizing - In. (mm) . . . . . 21

Table 8 – Opening Dimensions - In. (mm) . . . . . . . . . . . . . . . . . 21

Table 9 – Filter Media Pressure Drop (Clean) Versus Airflow - In.

W.C. (Pa) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Table 10 – Filter Media Pressure Drop (Clean) Versus Face Velocity-

In. W.C. (Pa) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

AIR DUCTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Table 11 – Air Delivery - CFM (With Filter) . . . . . . . . . . . . . . . 22

GAS PIPING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Table 12 – Maximum Capacity of Pipe . . . . . . . . . . . . . . . . . . . . 24

ELECTRICAL CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Table 13 – Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

VENTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Table 14 – Vent Termination Kit for Direct Vent (2-pipe) Systems29

Table 15 – Hanger Spacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Table 16 – Approved Combustion-Air and Vent Pipe, Fitting and Ce

ment Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Table 17 – Maximum Allowable Exposed Vent Length in Uncondi

tioned Space - Ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Table 18 – Maximum Equivalent Vent Length - Ft. . . . . . . . . . . 38

Table 19 – Deductions from Maximum Equivalent Vent Length - Ft.

(M) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

START-UP, ADJUSTMENT, AND SAFETY CHECK . . . . . . . . . 44

Table 20 – Altitude Derate Multiplier for USA. . . . . . . . . . . . . . 45

Table 21 – Gas Rate (CU ft./hr). . . . . . . . . . . . . . . . . . . . . . . . . . 47

Table 22 – Gas Valve Outlet Pressure for Gas Heat Values at Altitude

- 40,000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Table 23 – Gas Valve Outlet Pressure for Gas Heat Values at Altitude

- 60,000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Table 24 – Gas Valve Outlet Pressure for Gas Heat Values at Altitude

- 80,000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Table 25 – Gas Valve Outlet Pressure for Gas Heat Values at Altitude

- 100,000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

SERVICE AND MAINTENANCE PROCEDURES. . . . . . . . . . . . 50

WINTERIZATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

PARTS REPLACEMENT INFORMATION GUIDE . . . . . . . . . . . 58

MODEL NOMENCLATURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Most states in the USA and jurisdictions in Canada have laws that

require the use of Carbon Monoxide (CO) alarms with fuel burning

products. Examples of fuel burning products are furnaces, boilers, space

heaters, generators, water heaters, stoves/ranges, clothes dryers,

fireplaces, incinerators, automobiles, and other internal combustion

engines. Even if there are no laws in your jurisdiction requiring a CO

Alarm, it’s highly recommended that whenever any fuel burning product

is used in or around the home or business that the dwelling be equipped

with a CO Alarm(s). The Consumer Product Safety Commission

recommends the use of CO Alarm(s). The CO Alarm(s) must be

installed, operated, and maintained according to the CO Alarm

manufacturer’s instructions. For more information about Carbon

Monoxide, local laws, or to purchase a CO Alarm online, please visit the

following website. https://www.kidde.com.

A200352

Portions of the text and tables are reprinted from NFPA 54/ANSI Z223.1E, with permission of National Fire Protection Association, Quincy, MA

02269 and American Gas Association, Washington DC 20001. This reprinted material is not the complete and official position of the NFPA or ANSI

on the referenced subject, which is represented only by the standard in its entirety.

PG95ESU

Up to 95% AFUE, Single-Stage, Upflow/Horizontal

Ultra Low NOx, 35-in. Tall, Condensing Gas Furnace

(Minor Series B)

WARNING

CARBON MONOXIDE POISONING HAZARD

Failure to follow this warning could result in personal injury and/or

death.

Carbon Monoxide (CO) is a colorless, odorless, and tasteless poisonous

gas that can be fatal when inhaled. Follow all installation, maintenance,

and service instructions. See additional information below regarding

the installation of a CO Alarm.

Summary of Contents for PG95ESU



























































Search results

Summary of Contents for PG95ESU

Reviews:

Related manuals for PG95ESU

Brands by name

Popular brands

Carrier PG95ESU, User Manual

Search results

Summary of Contents for PG95ESU

Reviews:

Related manuals for PG95ESU

Brands by name

Popular brands