background image

PG95ESU: Installation, Start-up, Operating and Service Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

33

A14546

Fig. 46 – Near Furnace Vent Connections

Install the Vent and Combustion Air Pipes

With the furnace installed in the required position, remove the desired

knockouts from the casing. It will be necessary to remove one knockout

for  the  vent  pipe  and  the  other  knockout  for  the  combustion  air

connection (see 

Fig. 12

).

Use a flat blade screwdriver and tap on the knockout on opposite sides,

where the knockout meets the casing. Fold the knockout down with duct

pliers and work the knockout back and forth until it is removed. Trim

any excess metal from the knockout with tin snips.
The vent elbow can be rotated to the required location on the casing if

necessary

 

(see 

Fig. 48

). To rotate the vent elbow:

1. Loosen  the  clamp  on  the  inlet  of  the  vent  elbow  attached  to  the

inducer.

2. Rotate the vent elbow to the required position. There are rounded

notches on the vent elbow to align it with the inducer housing for

each orientation.

3. Tighten the clamp around the vent elbow. Torque the clamp to 15

lb-in. (see 

Fig. 50

 through 

Fig. 52

).

Installing the Vent Pipe Adapter and Combustion Air 

Pipe Adapter

NOTE: 

The rubber coupling that attaches to the vent pipe adapter must

be used. The adapter seals the vent pipe to the casing and reduces the

strain on the vent elbow attached to the inducer.

1. Apply  the  gaskets  to  the  vent  pipe  and  combustion  air  pipe

adapters. If supplied, remove and discard round center “slug” from

interior of gasket (see 

Fig. 47

).

NOTE: 

The vent pipe adapter can be distinguished from the inlet pipe

adapter by the absence of an internal pipe-stopping ring. The vent pipe

can pass through the vent pipe adapter; it cannot pass through the inlet

pipe adapter.

2. Align  the  screw  holes  in  the  plastic  vent  pipe  adapter  with  the

dimples in the casing.

3. Pilot drill the screw holes for the adapter in the casing and attach

the vent pipe adapter to the furnace with sheet metal screws

4. Slide the end of the rubber vent coupling with notches in it over the

standoffs on the vent pipe adapter.

5. Insert a length of vent pipe through the coupling into the outlet of

the vent elbow.

6. Tighten the clamp around the outlet of the vent elbow. Torque the

clamp to 15 lb-in.

A13074

Fig. 47 – Vent Coupling and Adapter with Gaskets

A210034

Fig. 48 – Inducer Vent Elbow

Install the remaining vent and combustion air pipes as shown below. It is

recommended that all pipes be cut, prepared, and pre-assembled before

permanently cementing any joint.

1. Working from furnace to outside, cut pipe to required length(s).
2. De-burr inside and outside of pipe.
3. Chamfer outside edge of pipe for better distribution of primer and

cement.

4. Complete  the  vent  and  combustion  air  pipe  installation  by

connecting  the  concentric  vent  or  by  installing  the  required

termination elbows (see 

Fig. 56

 and 

Fig. 57

).

For Ventilated Combustion Air Termination (see 

Fig. 58

).

5. Clean and dry all surfaces to be joined.
6. Check dry fit of pipe and mark insertion depth on pipe.

WARNING

!

CARBON MONOXIDE POISONING HAZARD

Failure to follow this warning could result in personal injury or death. 

To route the vent pipe and combustion air pipe through the furnace, the

manufacturer  supplied  kit  must  be  used.  Failure  to  properly  seal  the

blower  compartment  from  the  furnace  vestibule  could  result  in  the

circulation of carbon monoxide throughout the structure. The vent pipe

and  combustion  air  pipe  must  be  a  continuous  pipe  while  passing

through  the  blower  compartment.  Seals  supplied  in  this  kit  must  be

installed per the instructions provided. Follow all procedures outlined

in these instructions.

WARNING

!

CARBON MONOXIDE POISONING HAZARD

Failure to follow this warning could result in personal injury or death.

DO NOT

 use cement to join polypropylene venting systems. Follow

the  polypropylene  venting  system  manufacturer’s  instructions  for

installing polypropylene venting systems.

Avoid short horizontal offsets with 90
deg. Elbows. Short offsets can be
difficult to slope and may trap con-
densate.

Use 45 deg. Elbows where
possible, to ensure conden-
sate drainage.

Slope vent pipe back to the 
furnace at least ¼” per foot 

NOTICE

!

The following instructions are for PVC/ABS DWV vent piping only.

DO  NOT  USE  THESE  TECHNIQUES  FOR  POLYPROPYLENE

VENT  PIPING  SYSTEMS.  See  the  polypropylene  vent  system

manufacturer’s  instructions  for  installing  polypropylene  venting

systems.

Attach gaskets to vent pipe and
combustion air adapters.

Vent Coupling and Adapter

Summary of Contents for PG95ESU



























































Reviews: