Lincoln Vrtex 360 Operator'S Manual Download

Page: 13 / 53

TILTING

Place the

VRTEX

360 directly on a secure, level sur-

face.

A-3

INSTALLATION

VRTEX

360

A-3

HIGH FREQUENCY INTERFERENCE PRO-
TECTION

READ ENTIRE INSTALLATION SECTION BEFORE
STARTING INSTALLATION.

Safety Precautions

------------------------------------------------------------

SELECT SUITABLE LOCATION

The machine will not operate in harsh environments.
It is important that simple preventative measures are
followed in order to assure long life and reliable opera-
tion. This product is for INDOOR USE ONLY.

• Dirt and dust that can be drawn into the machine

should be kept to a minimum. Failure to observe
these precautions can result in excessive operating
temperatures and nuisance shutdown.

• Do not locate where monitor is exposed to direct

sunlight.

• Do not place equipment near radiant heat sources.

• Do not place in a confined space. Allow a minimum

of 3 feet of clearance around machine and stand at
all times. Adequate ventilation is necessary.

• The circuit breaker switch on the rear panel is the

input power disconnect device. Do not position the
equipment so that it is difficult to operate the circuit
breaker.

• Route and protect power cable to minimize exposure

to damage.

ENVIRONMENTAL AREA

Keep the machine inside and dry at all times. Do not
place it on wet ground or in puddles. Never place liq-
uids on top of the machine.

STACKING

The

VRTEX

360 cannot be stacked.

ELECTRIC SHOCK can kill.

•

Only qualified personnel should per-
form this installation.

• Turn the input power OFF and

unplug the machine from the recep-
tacle before working on this equip-
ment.

•

insulate yourself from the work and ground.

• Always connect the

VRTEX

360

to a power sup-

ply grounded according to the National Electrical
Code and local codes.

WARNING

CAUTION

USE CAUTION WHEN OPERATING THIS MACHINE
AROUND OTHER EQUIPMENT.

•

Large equipment, such as cranes, may interfere
with the operation of this machine.

• This machine may interfere with the operation of

other equipment in work/training area.

• Lift only with equipment of ade-

quate lifting capacity.

• Be sure machine is stable when

lifting.

• Do not operate machine while

suspended or when lifting.

FALLING EQUIPMENT can cause injury.
------------------------------------------------------------------------

WARning

Lifting

If lifting the

VRTEX

360

is required, use two straps, each

rated for 500 pounds (226.8 kg) or more. Do not attempt to
lift the

VRTEX

360

with accessories attached to it.

STRAPS

Summary of Contents for Vrtex 360






















































Search results

Summary of Contents for Vrtex 360

Reviews:

Related manuals for Vrtex 360

Brands by name

Popular brands

Lincoln Vrtex 360, Operator'S Manual

Search results

Summary of Contents for Vrtex 360

Reviews:

Related manuals for Vrtex 360

Brands by name

Popular brands