Lincoln Electric Vantage 500 CE Operator'S Manual Download Page 16

Page: 16 / 42

B-4

OPERATION

B-4

ENGINE CONTROLS:

12. RUN/STOP SWITCH

- RUN position ener-

gizes the engine prior to starting. STOP position

stops the engine. The oil pressure interlock

switch prevents battery drain if the switch is left in

the RUN position and the engine is not operating.

13. GLOW PLUG PUSH BUTTON

• When pushed activates the glow plugs. Glow plug

should not be activated for more than 20 seconds

continuously.

14. START PUSH BUTTON

- Energizes the

starter motor to crank the engine.

15. IDLER SWITCH

- Has two positions as follows:

1) In the HIGH position, the engine runs at the high

idle speed controlled by the engine governor.

2) In the AUTO position, the idler operates as fol-

lows:

• When switched from HIGH to AUTO or after

starting the engine, the engine will operate at full

speed for approximately 12 seconds and then go

to low idle speed.

• When the electrode touches the work or power is

drawn for lights or tools (approximately 100

Watts minimum), the engine accelerates and

operates at full speed.

• When welding ceases or the AC power load is

turned off, a fixed time delay of approximately 12

seconds starts. If the welding or AC power load

is not restarted before the end of the time delay,

the idler reduces the engine speed to low idle

speed.

• The engine will automatically return to high idle

speed when there is welding load or AC power

load reapplied.

16. ELECTRIC FUEL GAUGE-

The electric fuel

gauge gives accurate and reliable indication as to

how much fuel is in the fuel tank.

17. ENGINE HOUR METER-

Displays the total

time that the engine has been running. This meter

is useful for scheduling prescribed maintenance.

18. ENGINE PROTECTION LIGHT-

A warning indi-

cator light for Low Oil Pressure and/or Coolant Over

Temperature.The light is off when the systems are func-

tioning properly. The light will come on and the engine

will shutdown when there is Low Oil Pressure and/or

the Coolant is Over Temperature.

Note:

The light remains off when the RUN-STOP switch

is in the "ON" position prior to starting the

engine.However if the engine is not started within 60

seconds the light will come on. When this happens the

RUN-STOP switch must be returned to the "OFF" posi-

tion to reset the engine protection system and light.

19. BATTERY CHARGING LIGHT-

A warning indica-

tor light for Low/No battery charge. The light is off when

the systems are functioning properly. The light will

come on if there is a Low/No battery condition but the

machine will continue to run.

Note:

The light may or may not come on when the RUN-

STOP switch is in the "ON" position. It will come on dur-

ing cranking and stay on until the engine starts. After

starting the engine the light will go off unless a Low/No

battery charge condition exists.

20. COOLANT TEMPERATURE GAUGE-

A indica-

tor of engine coolant temperature.

21. OIL PRESSURE GAUGE-

A indicator of engine

Oil Pressure.

22. CIRCUIT BREAKER

STARTING THE ENGINE

1. Remove all plugs connected to the AC power recepta-

cles.

2. Set IDLER switch to AUTO.

3. Press Glow Plug Button and hold 15 to 20 seconds.

4. Set the RUN/STOP switch to RUN.

5. Press START button until the engine starts or for up to 10

seconds. Continue to hold the glow plug button for up to

an additional 10 seconds.

6. Release the engine START button immediately when the

engine starts.

7. The engine will run at high idle speed for approximately

12 seconds and then drop to low idle speed. Allow the

engine to warm up at low idle for several minutes before

applying a load and/or switching to high idle. Allow a

longer warm up time in cold weather.

VANTAGE

500 (CE)

TYPICAL VANTAGE® 500 (CE) FUEL CONSUMPTION

TABLE B.2

PERKINS (404C-22T), (404D-22T)

Gal./Hr (Liters/Hr)

.31(1.16)

.47(1.78)

1.82(6.87)

Low Idle - No Load

1200 R.P.M.

High Idle - No Load

1575 R.P.M.

DC Weld Output

450 Amps @ 38Volts

NOTE: This data is for reference only. Fuel consumption is

approximate and can be influenced by many factors, including

engine maintenance, environmental conditions and fuel quality.

Codes 11298, 11298

15 gallon tank

49.13

31.89

8.26

Codes 11524, 11525

11574,11575

20 gallon tank

65.50

42.52

11.01

Running Time ( Hours)

Summary of Contents for Vantage 500 CE











































Search results

Summary of Contents for Vantage 500 CE

Reviews:

Related manuals for Vantage 500 CE

Brands by name

Popular brands

Lincoln Electric Vantage 500 CE, Operator'S Manual

Search results

Summary of Contents for Vantage 500 CE

Reviews:

Related manuals for Vantage 500 CE

Brands by name

Popular brands