Lincoln Electric RED-D-ARC DX450 Operator'S Manual Download Page 12

The  standard  muffler  included  with  this  welder  does

not qualify as a spark arrester. When required by local

regulations,  a  suitable  spark  arrester,  such  as  the

K903-1 must be installed and properly maintained.

An incorrect spark arrestor may lead to damage to

the engine or adversely affect performance.

------------------------------------------------------------------------

REMOTE CONTROL

The DX450 is equipped with a 3-pin and a 14-pin con-

n e c t o r .   W h e n   i n   t h e   C C - S T I C K ,   C V - W I R E   O R

GOUGE  modes  and  when  a  remote  control  is  con-

nected to the 3-pin Connector, the auto-sensing circuit

automatically switches the OUTPUT control from con-

trol at the welder to remote control.

When  in  TOUCH  START  TIG  mode  and  when  a

Amptrol  is  connected  to  the  3-Pin  Connector,  the

OUTPUT  dial  is  used  to  set  the  maximum  current

range of the CURRENT CONTROL of the Amptrol.

When  in  the  DOWNHILL  PIPE  mode  and  when  a

remote  control  is  connected  to  the  3-Pin  or  14-Pin

connector,  the  output  control  is  used  to  set  the  max-

imum current range of the remote.

EXAMPLE: 

When  the  OUTPUT  CONTROL  on  the

welder  is  set  to  200  amps  the  current  range  on  the

remote  control  will  be  40-200  amps,  rather  than  the

full  40-300  amps.  Any  current  range  that  is  less  than

the full range provides finer current resolution for more

fine tuning of the output.

In the CV-WIRE mode, if the feeder being used has a

voltage  control  when  the  wire  feeder  control  cable  is

connected  to  the  14-Pin  Connector,  the  auto-sensing

circuit automatically makes OUTPUT CONTROL inac-

tive  and  the  wire  feeder  voltage  control  active.

Otherwise, the OUTPUT CONTROL is used to preset

the voltage.

The  14-pin  connector  is  used  to  directly  connect  a

wire  feeder  control  cable.  In  the  CV-WIRE  mode,

when the control cable is connected to the 14-pin con-

nector,  the  auto-sensing  circuit  automatically  makes

the  Output  Control  inactive  and  the  wire  feeder  volt-

age control active.

NOTE:  When  a  wire  feeder  with  a  built  in  welding

voltage control is connected to the 14-pin connec-

tor,  do  not  connect  anything  to  the  3-pin  connec-

tor.

------------------------------------------------------------------------

FUEL          

USE DIESEL FUEL ONLY- 

Low  Sulphur  fuel  or  ultra  low  sulphur  fuel  in  USA  and
CANADA only.

•  Fill the fuel tank with clean, fresh fuel. The capacity of

the    tank  is  20  gals.  (75.7  ltrs).  When  the  fuel  gauge
reads  empty  the  tank  contains  approximately  2  gals.
(7.6ltrs.) of reserve fuel.

NOTE: A  fuel  shut  off  valve  is  located    on  the  pre-fil-

ter/sediment filter. Which should be in the closed

position when the welder is not used for extend-

ed periods of time.

------------------------------------------------------------------------

ENGINE COOLING SYSTEM

Air to cool the engine is drawn in the side and exhaust-

ed through radiator & case back. It is important that the

intake  and  exhaust  air  is  not  restricted.  Allow  a  mini-

mum clearance of 1ft. (0.6m) from the case back and 16

in.  (406mm)  from  either  side  of  the  base  to  a  vertical

surface

.

------------------------------------------------------------------------

BATTERY CONNECTION

Use  caution  as  the  electrolyte  is  a  strong  acid  that  can

burn skin and damage eyes.

------------------------------------------------------------------------

The  DX450  is  shipped  with  the  negative  battery  cable  dis-

connected.  Make  certain  that  the  RUN-STOP  switch  is  in

the STOP position. Remove the two screws from the battery

tray using a screwdriver or a 3/8"(10mm) socket. Attach the

negative  battery  cable  to  the  negative  battery  terminal  and

tighten using a 1/2"(13mm) socket or wrench.

NOTE

:  This  machine  is  furnished  with  a  wet  charged

battery; if unused for several months, the battery may

require a booster charge. Be careful to charge the bat-

t e r y   w i t h   t h e   c o r r e c t   p o l a r i t y .   ( S e e   B a t t e r y   i n

“Maintenance Section”)

MUFFLER OUTLET PIPE

Using the clamp provided secure the outlet pipe to the

outlet  tube  with  the  pipe  positioned  such  that  it  will

direct  the  exhaust  in  the  desired  direction.  Tighten

using a 9/16"(14mm) socket or wrench.

SPARK ARRESTER

Some  federal,  state  or  local  laws  may  require  that

gasoline  or  diesel  engines  be  equipped  with  exhaust

spark  arresters  when  they  are  operated  in  certain

locations  where  unarrested  sparks  may  present  a  fire

hazard.

A-4

INSTALLATION   

A-4

WARNING

CAUTION

WARNING

WARNING

WARNING

DX450   (RED-D-ARC)

Summary of Contents for RED-D-ARC DX450



















































Reviews: