manualshive.com logo in svg

Lincoln Electric Power MIG 350MP, Operator'S Manual

Share
Download
Lincoln Electric Power MIG 350MP Operator'S Manual Download Page 30

D-2 

D-2

MAINTENANCE

4. Insert the untrimmed Liner into the back end of the

gun.

5. Seat Liner bushing into back of gun. Secure Liner

by tightening set screw. Do not install the gas dif-
fuser at this time.

6. Lay the cable straight and trim Liner to 9/16”.

Remove burrs.

7. Install insulator and secure the gas diffuser into the

tube.

Excessive pressure at the start may cause the dirt
to form a plug.

-----------------------------------------------------------

Flex the cable over its entire length and again blow
out the cable. Repeat this procedure until no further
dirt comes out. If this has been done and feed prob-
lems are experienced, try liner replacement, and refer
to trouble shooting section on rough wire feeding.

LINER REMOVAL AND REPLACEMENT

(SEE FIGURE D.1)

LINER REMOVAL, INSTALLATION AND TRIMMING
INSTRUCTIONS FOR MAGNUM 350MP

NOTE: The variation in cable lengths prevents the
interchangeability of liners between guns. Once a liner
has been cut for a particular gun, it should not be
installed in another gun unless it can meet the liner
cutoff length requirement. Liners are shipped with the
jacket of the liner extended the proper amount.

1. Remove the gas nozzle.

2. Remove the gas diffuser from the gun tube. 

3. Lay gun and cable out straight on a flat surface.

Loosen set screw of the connector on the back end
of the gun.

CAUTION

.56" (14.2mm)

LINER TRIM

LENGTH

Gun Tube 
Assembly

Insulator

Gas Diffuser

Gas Nozzle

Contact Tip

INSULATION TUBE

FEEDER END
CABLE HANDLE

BRASS CABLE
CONNECTOR

SET SCREW

MOLDED GAS PLUG

LINER ASSEMBLY(LINER BUSHING TO BE SEATED
TIGHT AGIANST BRASS CABLE CONNECTOR)

FIGURE D.1

POWER MIG

®

350MP

Summary of Contents for Power MIG 350MP
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands