manualshive.com logo in svg

Lincoln Electric Power MIG 350MP, Operator'S Manual

Share
Download
Lincoln Electric Power MIG 350MP Operator'S Manual Download Page 17

B-4

B-4

OPERATION 

POWER MIG

®

350MP

SETTING AND CONFIGURING THE POWER

MIG

®

350MP FOR WELDING

• Check that the electrode polarity is correct for the process

and turn the Power Switch to the "ON" position. After the
"boot-up" period (approximately 20 seconds), the POWER
MIG

®

350MP will default to the last preset weld mode that

was active when the machine was powered down. The
Multi-Process Panel defaults with the "Weld Mode" active.

• Toggle the SET switch to the desired "Weld Mode" opera-

tion. The Multi-Process Meter displays a weld mode num-
ber corresponding to a CC or CV welding process as
detailed by the chart on the right side of the panel. In the
example shown in Figure B.2 “

3”

is displayed above the

SET switch.  This means that the machine is set for CC-
GTAW (TIG) welding.

• Toggle the SELECT switch to activate the "weld parame-

ters" for the selected weld mode.

• Set each parameter using the SET switch to adjust the

parameter displayed on the display meter. 

NOTE:

 

If the LED next to the weld parameter is flashing, the

WFS/AMP and/or the Volt/Trim values can also be adjusted
for that parameter using the control knobs below each dis-
play meter. An LED below each of the displays will also be
flashing to indicate which value is adjustable.  

The Table B.1 shows which weld parameters are adjustable
for a given weld mode. The weld parameters are detailed
later in this  section.

PREFLOW /       RUN IN    START

ARC CONTROL        CRATER        BURNBACK          SPOT

POSTFLOW

CC-STICK

-----

-----

Yes

Yes

-----

-----

-----

CC-GTAW   POSTFLOW         -----

Yes

-----                       -----

-----

-----

CV-FCAW

-----

Yes

Yes

Yes

Yes

Yes

Yes

CV-GMAW

Yes

Yes

Yes

Yes

Yes

Yes

Yes

CV-GMAW-P

Yes

Yes

Yes

Yes

Yes

Yes

Yes

POWER

Yes

Yes

Yes

Yes

Yes

Yes

Yes

 3

 3

FIGURE B.2

TABLE B.1

Summary of Contents for Power MIG 350MP
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands