C-8
ACCESSORIES
C-8
K1548-1 LINC NET RECEPTACLE
KIT (INPUT AND OUTPUT)
LINC NET RECEPTACLE (OUTPUT)
Optional Output Connector Installation into the Control
Box Cabinet and/or into the Feeder Head Enclosure.
Control Box Cabinet Procedure
1. Turn off power.
2. Remove the screws from the front of the lower
and middle option panels of the User
Interface cabinet.
3. Tilt the option panels away from the front opening
of the Control Box cabinet. If the option panel has
an electrical connector, disconnect it from the
main printed circuit board (note connection point
for re-connection later). Remove the option panel
and set aside.
4. Remove the plastic plug (black) from the left hole
in the bottom of the Control Box cabinet and store
it in the bottom of the Control Box cabinet for
future use, should the Optional Output Connector
be removed.
5. Place the Optional Output Connector (Amphenol)
through the hole opened by the previous step
(place from the inside, out). Rotate the Optional
Output Connector so itʼs aligning key is positioned
to the front of the Control Box cabinet. Fasten the
Optional Output Connector to the bottom wall of
the Control Box cabinet with the four screws pro-
vided.
6. Secure the choke (large circular component of the
Optional Output Connector) by inserting itʼs leads
into the white nylon clip located near the Optional
Output Connector on the back wall of the Control
Box cabinet. Insert the choke leads only.
7. The Optional Output Connector has two internal
connectors, a four pin, and a single lead connec-
tor. Connect the four pin connector to the unused
four pin connector on the main printed circuit
board. Connect the single lead connector to a
similar connector found on a lead nearby that
branches out of the Control Box wiring harness.
8. Re-install the lower and middle option panels by
reversing the removal process. While re-installing the
option panels, ensure clearance between Optional
Output Connector components, Control Box wiring
harness, and option panel harness (if any).
Feeder Head Enclosure Procedure
1. Turn power off.
2. Remove the Feeder Head rear access door. The
Feeder Head cover can be removed to aid instal-
lation, but is not required.
3. Remove the plastic plug (black) from the hole at
the right rear of the Feeder Head and store it in
the left side of the Feeder Head rear compart-
ment for future use, should the Optional Output
Connector be removed.
4. Disconnect a printed circuit board connector
located at the bottom right corner of the printed
circuit board and position it to the left so as to pro-
vide clear access to the lower right corner of the
Feeder Head enclosure.
5. Place the Optional Output Connector (Amphenol)
through the hole opened by the two previous
steps (place from the inside, out). Rotate the
Optional Output Connector so itʼs aligning key is
positioned to the top of the Feeder Head enclo-
sure. Fasten the Optional Output Connector to
the back wall of the Control Box cabinet with the
four screws provided.
6. Secure the choke (large circular component of the
Optional Output Connector) by inserting itʼs leads
into the white nylon clip located near the Optional
Output Connector on the floor of the Feeder
Head. Insert the long choke leads rather than the
short leads that run between the choke and the
Output Connector. Insert the choke leads only.
7. The Optional Output Connector has two internal
connectors, a four pin, and a single lead connec-
tor. Connect the four pin connector to the unused
four pin connector on the printed circuit board.
Connect the single lead connector to a similar
connector found on a lead nearby that branches
out of the Feeder Head wiring harness.
8. Reconnect the printed circuit board connector that
was disconnected earlier.
9. Replace the rear access door and Feeder Head
cover if removed.
POWER FEED 10
Summary of Contents for POWER FEED IM584-D
Page 63: ...NOTES POWER FEED 10...
Page 64: ...NOTES POWER FEED 10...
Page 65: ...NOTES POWER FEED 10...