Lincoln Electric INVERTEC POWER WAVE 450 IM524-D Operator'S Manual Download Page 6

Thank You

for selecting a 

QUALITY

product by Lincoln Electric. We want you

to take pride in operating this Lincoln Electric Company product •••
as much pride as we have in bringing this product to you!

Read this Operators Manual completely

before attempting to use this equipment. Save this manual and keep it

handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.
The level of seriousness to be applied to each is explained below:

WARNING

This statement appears where the information 

must

be followed 

exactly

to avoid 

serious personal injury

or

loss of life

.

This statement appears where the information 

must

be followed to avoid 

minor personal injury

or

damage to

this equipment

.

CAUTION

Please Examine Carton and Equipment For Damage Immediately

When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims
for material damaged in shipment  must be made by the purchaser against the transportation company at the
time the shipment is received.

Please record your equipment identification information below for future reference. This information can be found
on your machine nameplate.

Model Name & Number _____________________________________

Code & Serial Number _____________________________________

Date of Purchase    _____________________________________

Whenever you request replacement parts for or information on this equipment always supply the information you
have recorded above.

v

v

Summary of Contents for INVERTEC POWER WAVE 450 IM524-D























































Reviews: