Lincoln Electric FLEXTEC350x CE CONSTRUCTION Operator'S Manual Download Page 25

 

English  

English 

22

 

WEEE 

07/06 

Engl

is

h

 

 

Do not dispose of electrical equipment together with normal waste! 
In observance of European Directive 2012/19/EC on Waste Electrical and Electronic Equipment (WEEE) 
and its implementation in accordance with national law, electrical equipment that has reached the end of its 
life must be collected separately and returned to an environmentally compatible recycling facility. As the 
owner of the equipment, you should get information on approved collection systems from our local 
representative. 
By applying this European Directive you will protect the environment and human health! 

 

Spare Parts 

12/05 

For Spare Parts references visit the Web page: https://www.lincolnelectric.com/LEExtranet/EPC/ 
 

Authorized Service Shops Location 

09/16 

 

The purchaser must contact a Lincoln Authorized Service Facility (LASF) about any defect claimed under Lincoln's 
warranty period. 

 

Contact your local Lincoln Sales Representative for assistance in locating a LASF or go to 
www.lincolnelectric.com/en-gb/Support/Locator. 

 
 

Summary of Contents for FLEXTEC350x CE CONSTRUCTION






























Reviews: