background image

Page 4 of 23

Safety instruction

General

Important information

Important information on LINAK

®

 products can be found under the following 

headings:

Warning!

Failure to comply with these instructions may result in accidents involving 
serious personal injury.

Failing to follow these instructions can result in the product being damaged 
or being destroyed.

Safe use of the system is possible only when the operating instructions are read 
completely and the instructions contained are strictly observed.
Failure to comply with instructions marked with the ”NOTE” symbol may result in 
serious damage to the system or one of its components.

It is important for everyone who is to connect, install, or use the systems to 
have the necessary information and access to this User Manual. Follow the 
instructions for mounting – risk of injury if these instructions are not followed.

The appliance is not intended for use by young children or infirm persons 
without supervision.

If there is visible damage on the product it must not be installed.

Note that during construction of applications, in which the actuator is to 
be fitted, there must be no possibility of personal injury, for example the 
squeezing of fingers or arms.

Assure free space for movement of application in both directions to avoid 
blockade.

Summary of Contents for DESKLINE DL1A
























Reviews: