READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING LUMINAIRE
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
IS:4091216
INSTRUCTION SHEET NO.
A0304
Page 1 of 1
COMPANY
a
631 Airport Road, Fall River, MA 02720
INSTRUCTION SHEET FOR 9”,12”&16” PENDALYTE™ POWERHEAD
POWERHEAD
Fig.
2
8-32
SCREWS
ALUMINUM REFLECTOR
SPACER COLLAR
To wire POWERHEAD to suspension kit (Standard, Stem, and Deco suspension kits sold
separately) follow instructions enclosed with individual suspension kit and connect as follows:
Using wire nuts (local hardware item) connect black lead to hot (black) power lead, connect
white lead to neutral (white) power lead, connect green/bare leads to ground (green) lead.
METAL HALIDE FIXTURES: refer to wiring diagram in fig. 1.
HID BALLAST
277V
240V
208V
120V
BLACK
WHITE
COMMON
GROUND
GROUND
POWERCORD
Fig. 1
CONNECT TO APPROPRATE VOLTAGE
9”ALUMINUM REFLECTOR INSTALLATION
1.
Locate 8-32 SCREWS, (supplied with POWERHEAD).
2.
Align holes in ALUMINUM REFLECTOR with threaded holes in SPACER COLLAR. (Fig. 2)
3.
Install 8-32 SCREWS and tighten evenly.
1.
Locate RETAINER CUP, GASKET STRIPS and 8-32 SCREWS, (supplied with POWERHEAD).
Thoroughly clean aluminum retainer cup to insure good adhesion of GASKET STRIPS. Peel off
ADHESIVE BACKING and apply GASKET STRIPS to retainer, equally spaced, as shown. (Fig. 3)
2.
Support glass shade in place, align evenly with extruded collar, and align RETAINER CUP with
THREADED INSERTS in socket plate.
3.
Install 8-32 SCREWS and tighten evenly to compress gasket strips.
CAUTION
:
Wear safety glasses. Glass is fragile. Handle with care. Broken glass may pose
a personal safety hazard.
9” GLASS SHADE INSTALLATION
NOTE: Natural oils and soil may discolor and stain glass finish. Wearing clean cotton gloves is recommended.
12”&16” REFLECTOR/REFRACTOR INSTALLATION
1.
Slide COLLAR up extruded NECK.
2.
Peel off backing of FOAM GASKET and adhere to TABS on SOCKET MOUNT PLATE. (Fig. 4)
3.
Tip Reflector/Refractor over SOCKET MOUNT PLATE and allow Reflector/Refractor to rest on
FOAM GASKET.
4.
To secure Reflector/Refractor align SLOT in
COLLAR over PINS and slide COLLAR down
NECK. Twist COLLAR counter-clockwise allowing
PIN to rest in NOTCH.
12” REFRACTOR SUPPORT
REFRACTOR SUPPORT PLATE and SUPPORT
PLATE SCREWS ARE supplied with all 12” HID
units.
1.
Install Acrylic Refractor per instructions above.
2.
Align REFRACTOR SUPPORT PLATE over
SOCKET MOUNT PLATE. (Fig. 4)
3.
Secure REFRACTOR SUPPORT PLATE with
SUPPORT PLATE SCREWS.
COLLAR
NECK
FOAM
GASKET
SOCKET
MOUNT
PLATE
TAB
REFRACTOR
SUPPORT
PLATE
SUPPORT
PLATE
SCREWS
PIN
POWERHEAD
Fig.
4
NOTCH
SLOT
Note: This instruction sheet covers several luminaire styles. Powerhead assembly, lamp type, and reflector style may vary slightly from that
shown, although installation is the same.
CAUTION:
12” HID units with Acrylic Refractor
must have REFRACTOR SUPPORT PLATE
installed.
MAXIMUM WATTAGE AS MARKED ON LUMINAIRE MUST NOT BE
EXCEEDED.
CAUTION:
GASKET
STRIPS
RETAINER CUP
8-32
SCREWS
THREADED
INSERT
GLASS
SHADE
Fig.
3
ADHESIVE
BACKING
POWERHEAD
