Job Information
Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
"JSQPSU3PBE'BMM3JWFS."t t'BY
We reserve the right to change details of design, materials and finish.
XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt
Lighting Systems
LSB-12
1BHFPG
-ZUFTQSFBEÜ-4#1BSBCPMJD-PVWFS-JHIU51FS'PPU /PNJOBM4FDUJPO
#
Features
1. Housing:
Extruded alu
m
inu
m
. Die-cast end cap
m
echanically attached with
no exposed fasteners or hardware.
2. Lamping:
Two T8, 32 watt fluorescent la
m
ps per 4-foot section. Provided by
others.
3. Reflector:
Precision die-for
m
ed se
m
i-specular alu
m
inu
m
.
4. Louver:
Parabolic louver, low-iridescent se
m
i-specular anodized alu
m
inu
m
,
Electrical
Ballast is <10% THD, .98 ballast factor, instant start. 18 gauge wire. Color-coded
quick connectors allow ease of connection for joiner
m
odules. Power feed is 18
gauge white SJT. For special circuiting consult factory. Factory installed ballast
disconnect allows the ballast to be disconnected fro
m
and reconnected to inco
m
ing
power under load without turning the entire circuit off.
Dimming:
120/277 VAC 1% di
mm
ing level, 4 wire feed required.
Emergency Battery Pack:
32 watt: 450 lu
m
ens @ 90
m
inutes, 4 wire feed
required.
Mountings
Finish
Powder coated baked white or alu
m
inu
m
finish. Custo
m
colors available, consult
factory.
Options and Accessories
E
m
ergency circuiting; special circuiting; X, T & L joiner blocks - consult factory.
Labels
UL, cUL and I.B.E.W.
Ordering Instructions
Individual Fixtures:
1. Order nu
m
ber of MODULES required.
2. Order one POWER FEED END SET per MODULE.
Continuous Rows:
1. Deter
m
ine run length.
2. Order the appropriate nu
m
ber of MODULES for the co
m
plete run.
3. Order one POWER FEED END SET per run.
4. Order one CABLE ASSEMBLY per MODULE
m
inus one per run.
5. For runs that exceed a
m
perage li
m
its, order the appropriate nu
m
ber of
CABLE/CORD ASSEMBLIES.
Co
m
plete ordering instructions below.
Ordering Information
Fa
m
ily
La
m
ps
Voltage
Finish
2
= 2-La
m
p T8
C
= Parabolic Louver
AL
= Alu
m
inu
m
WH
= White
LSB
2
C
Length
Shielding
Ballast
1
= 120 volt
2
= 277 volt
4
= 4-Foot
8
= 8-Foot
41° shielding lengthwise, blades are 1-1/3” (3.39c
m
) high and 2” (5.08c
m
) O.C.
Louver fra
m
e is extruded alu
m
inu
m
and finished to
m
atch housing.
Cable suspension (not shown) - 4-1/2" (11.43c
m
) dia
m
eter canopy finished white
ena
m
el, 1/16" (0.16c
m
) dia
m
eter stainless steel aircraft cable adjustable up to 36”
(91.44c
m
). Dual-screw draw-tight connector to create hairline sea
m
between joiner
m
odules.
32
= 32W T8
3E
= 32W T8 E
m
ergency Pack
3D
= 32W T8 Di
mm
ing
Half Scale
1
2
4
3
8-1/2" (21.60 c
m
)
1-3/4" (4.45 c
m
)
3-1/4" (8.26 c
m
)
2-5/8" (6.67 c
m
)
