Restoring Factory Defaults
CAUTION:
When setting modules back to Factory
Defaults, you will be erasing ALL of the programming
that has been performed. Make sure you won’t be
loosing anything important before proceeding.
1.
Press and hold the Laser
button and aim laser
beam at an individual modules receiver to select it
and place it in program mode. (When using multiple
modules, select them in the same manner if they
need to be programmed identically to the first
module.) The module’s LED(s) will blink at a 1/2 sec-
ond rate when in program mode. The LRC’s LED will
also blink (every 1 second) to indicate the transmitter
will be transmitting program IR commands when but
tons are depressed. (After 60 seconds of inactivity,
the module(s) will exit the program mode without
saving.)
2.
Press and hold the Begin
b
button for greater than
3 seconds (the module’s LED(s) will blink rapidly and
then after 3 seconds stay on). Release the Begin
b
button. The module’s LED(s) will blink at a 1/4 second
rate. (After 60 seconds of inactivity, the module(s) will
exit the program mode without saving.)
3.
Press and hold the Laser button and aim laser
beam at the module(s) you are programming. This will
reinitialize the module to its factory defaults.
NOTE:
Any other sequence will prevent the Factory
Defaults from being set.
9. Troubleshooting
When I point the LRC at the TM and try to raise or lower
the light level of all of the modules, nothing happens.
• Check the LED on the LRC. If it is blinking, this means
you’re in select/program mode. In order to raise or
lower modules with a TM in this mode, you must
individually select the modules you want to change or
if you want all modules to raise or lower at the same
time, you must exit this mode first by pressing the
end
e
button.
When dimming, the module will continue to dim even
after I’ve stopped pressing the remote buttons.
• Because of the delay in receiving IR commands, the
desired light level may have been missed. Therefore
release the up
or down button’s prior to the
desired light level.
• Make sure there is a good ground throughout,
starting at the luminaire ground and ending with the
earth ground.
Factory Defaults
Factory Defaults for the DM
Address:
C1 (House "C", Unit "1")
IR: Disabled (When not in Program Mode)
Present Scene:
ON Scene
Present Level:
100%
OFF:
Level 0% - Fade 3 Sec
ON Scene:
Level 100% - Fade 3 Sec
A
Scene:
Level 86% - Fade 3 Sec
B
Scene:
Level 72% - Fade 3 Sec
C
Scene:
Level 58% - Fade 3 Sec
D
Scene:
Level 44% - Fade 3 Sec
E
Scene:
Level 30% - Fade 3 Sec
F
Scene:
Level 16% - Fade 3 Sec
G
Scene:
Level 13% - Fade 3 Sec
H
Scene:
Level 10% - Fade 3 Sec
I
Scene:
Level 7% - Fade 3 Sec
J
Scene:
Level 5% - Fade 3 Sec
K
Scene:
Level 3% - Fade 3 Sec
L
Scene:
Level 1% (Night Light) - Fade 3 Sec
Factory Defaults for the NDM
Address:
C1 (House "C", Unit "1")
IR:
Disabled (When not in Program Mode)
Present Scene:
ON Scene
Present Level:
100%
OFF:
Level 0% - Fade 0 Sec
ON Scene:
Level 100% - Fade 0 Sec
A-L Scene:
Level 100% - Fade 0 Sec
Factory Defaults for the TM
Address:
C1 (House "C", Unit "1")
IR:
Enabled
Present Scene:
ON Scene
Cycle ‘A’ Program:
Scenes A - B - C - D. All have
1.5 second fade rates and will
switch scenes every 3 seconds
Cycle ‘B’ Program:
Cleared
Cycle ‘C’ Program:
Cleared
Cycle ‘D’ Program:
Cleared
Cycle ‘E’ Program:
Cleared
Cycle ‘F’ Program:
Cleared
Verify:
Disabled
24
25
Scenes are only
available when
using a Lightolier
Controls Compose
8 Button Wall
Master. Consult
factory for more
information and
programming
instructions.
