LIGHT MY BRICKS LEGO Star Wars Slave 1 75060 Lighting Kit Installation Instructions Manual Download Page 27 | Manualshive

Page: 27 / 62

background image

Starting with the left 1x3 plate, take a

Blue 30cm Bit Light

and place it

over the stud furthest to the left. Secure it in place by connecting one of
the provided LEGO

Trans Light Blue Round Plate 1x1

directly over

the top. Discard the original trans light blue round tile.

Take another

Blue 30cm Bit Light

and place it over the next stud

along. Secure it in place by connecting another

Trans Light Blue

Round Plate 1x1

directly over the top. Repeat this step to install

«
...
25
26
27
28
29
...
»

Summary of Contents for LEGO Star Wars Slave 1 75060 Lighting Kit































































Reviews:

No comments

Related manuals for LEGO Star Wars Slave 1 75060 Lighting Kit

Brand: RASHA PROFESSIONAL Pages: 11

Brand: MADRIX Pages: 24

Brand: MADRIX Pages: 28

PowerXL DX-NET-ETHERNET2-2

Brand: Eaton Pages: 48

Power Xpert C445

Brand: Eaton Pages: 2

Brand: Ognibene Pages: 28

Brand: Hameg Pages: 24

Brand: Vaisala Pages: 118

Brand: M-Audio Pages: 12

Brand: M-Audio Pages: 64

Brand: M-Audio Pages: 16

Brand: M-Audio Pages: 4

Brand: M-Audio Pages: 52

Brand: Rath Pages: 5

Brand: Tar River Pages: 26

Brand: ZOLL Pages: 38

Brand: ZOLL Pages: 36

Nature2 Fusion soft

Brand: Zodiac Pool Systems Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands