LIGHT MY BRICKS LEGO Star Wars Slave 1 75060 Lighting Kit Installation Instructions Manual Download Page 1

Page: 1 / 62

Light My Bricks

Installation Instructions for Light My Bricks LED Lighting Kits
Jul 20

20 min read

Light My Bricks: LEGO Star Wars Slave 1

75060 Lighting Kit

The following page is the instructions for the

Light My Bricks LEGO

Star Wars Slave 1 (75060) LED light kit.

To ensure a trouble-free installation of your light kit, please read and
follow each step carefully.

If you run into any issues, please refer to the

online troubleshooting

guide.

To download this instructions guide in PDF format please click here.

Please note: This page lists instructions for the LED
light kit only. If you are wishing to purchase the Light
My Bricks LEGO Star Wars Slave 1 (75060) LED light
kit , please click here to view the product page

. . .

Package Contents:

13x

White 30cm Bit Lights

•

Summary of Contents for LEGO Star Wars Slave 1 75060 Lighting Kit































































Search results

Summary of Contents for LEGO Star Wars Slave 1 75060 Lighting Kit

Reviews:

Related manuals for LEGO Star Wars Slave 1 75060 Lighting Kit

Brands by name

Popular brands

LIGHT MY BRICKS LEGO Star Wars Slave 1 75060 Lighting Kit, Installation Instructions Manual

Search results

Summary of Contents for LEGO Star Wars Slave 1 75060 Lighting Kit

Reviews:

Related manuals for LEGO Star Wars Slave 1 75060 Lighting Kit

Brands by name

Popular brands