Light motion Urban 180 Instruction Manual Download Page 7

Installation of Urban

 

Fig 15: Urban on bar 

(strap over post).

Figure 17: Mount 

tight on helmet.

4

Urban System Operation

Normal Operation

The Light & Motion Urban LED lights all have one switch on the top of the head that controls power.  
A brief button push activates “Cruise” mode where you will find 4 settings: High, Medium, Low, and 
Flash.  A single click cycles through each of these settings.  Because our riders are versatile cyclists, 
we design our lights to accommodate those needs.    

Aiming your Urban

Light & Motion creates lights with optics designed to reflect the maximum amount of light and 
direct to where a rider needs it most.  Seca takes this one step further and introduces our 
proprietary  Gem-Beam  footprint  of  light,  which  clips  light  from  where  you  don’t  need  it  and 
redistributes it where you do.  
For best results at lower speeds, position your light so that you get ample fill/peripheral light in 
front of the tire from the flood portion of the beam. For faster speeds, you can position it slightly 
higher so that the spot portion of the beam shoots farther down the road giving you enhanced 
depth perception and a long line of site.

Battery Discharge Protection

All  Light & Motion lights incorporate a low battery warning and battery discharge protection 
circuit.  If the battery becomes discharged, the light head will automatically dim down to try and 
preserve battery life, this will occur with approximately 15 minutes of battery life to go.

Batter Status Indicator:  
The Urban has a battery status indicator, located on the back of the light. 

•       A 

green light

 indicates > 75% Charge 

•       A 

amber/yellow

 

light

 indicates > 50% Charge

•       A 

solid red light 

indicates > 25% Charge

•       A 

red flashing light

 indicates < 25% Charge

 
Auto-Shutoff
When  Urban  can’t  stay  on  any  longer  without  damaging  the  battery,  the  main  LED    will  flash 
quickly for 10 seconds and then shut off.  If you see this, hit the brakes and stop safely.  Once 
Urban has done an auto-shutoff, it will not operate again until it is charged.  This is to protect the 
battery, as there is no more useful charge in your system.

Summary of Contents for Urban 180











Reviews: