STEP 3
- SETTING THE CLOCK
NOTE: When you need to reset the clock, press and hold SET CLOCK until
“12
hr” appears. Release the button, and then repeat all parts of STEP 3.
1.
On the time display, “12
hr” appears. To select 24-hour time, press
+ or – .
2. Press SET CLOCK. The hour will flash. To change the hour, press + or – .
3. Press SET CLOCK. The minute will flash. To change the minute, press + or – .
4. Press SET CLOCK. The year will flash. To change the year, press + or – .
5. Press SET CLOCK. The small “
M
” and “
D
” will flash. To change to a day-first
display of the date, press + or –.
6. Press SET CLOCK. The month will flash. To change the month, press + or – .
8 . Press SET CLOCK. The “E” (for English) will flash. To change to
Spanish (”S”) or French (”F”), press + or – . Press SET CLOCK again.
9. The clock will show the day of the week to the right of the date.
If you prefer to display the year instead, press SET CLOCK again.
STEP 4
- SETTING THE WAKE-UP ALARM
NOTE: To change the wake-up alarm time, press and hold SET ALARM until the
wake-up hour flashes. Release the button, and then repeat all parts of STEP 4.
2. Press SET ALARM. The wake-up minute will flash. To change the minute, press + or – .
You can use the HI LO slide switch to adjust the volume of the wake-up alarm.
The emergency alarm always sounds at full volume.
ERROR MESSAGES
PLEASE READ THE USER’S MANUAL COMPLETELY AND THOROUGHLY FOR
FURTHER DIRECTIONS, PRODUCT FEATURES, AND WARRANTY INFORMATION.
7. Press SET CLOCK. The day of the month will flash. To change the day, press + or – .
3. Press ON/OFF to enable or disable the wake-up alarm. The bell icon at lower
For more information, visit www.lifetonesafety.com or call
1-800-648-7923 (
+1 405 200 1555 outside North America
).
MODEL HLAC151
Battery Error
Bed-Shaker Error
BEEP!
BEEP!
Batteries:
If the clock is flashing “BATT” and beeping at one-minute intervals, the
batteries were not installed correctly or are below the required voltage. Remove
and reinsert them, or replace them if necessary. Be sure to match the polarity signs
(+ and –) in the battery compartment. To keep the setup with your smoke alarm,
leave the clock plugged in while you change batteries.
Bed shaker:
If the screen is flashing “
bed
s
” and the clock is beeping, the bed shaker
has probably come unplugged. Seat the bed-shaker plug firmly into the jack.
NOTE: If you want to stop using the bed shaker after it has been installed, unplug
it and then press and hold the red TEST/SILENCE button for 2 seconds. That starts
a manual self-test that will display “TEST” for 10 to 20 seconds, sound the fire alarm
briefly, and “retrain” the HL to operate without a bed shaker.
If you decide to start
using the bed shaker again, simply plug it in.
Buttons on the Top of the Lifetone HL™
left appears when the alarm is enabled and disappears when the alarm is disabled.
WAKE-UP TIME
BELL
HOUR
MINUTE
DAY
MONTH
MONTH OR
DAY FIRST
YEAR,
LANGUAGE,
DAY OF WEEK
(OR DAY)
(OR MONTH)
KEEP THIS QUICK-START GUIDE IN A SAFE PLACE
Doc# LTQSG151E131227
800 Research Parkway, Suite 339
Oklahoma City, OK 73104
1. If the wake-up hour isn’t already flashing, press and hold SET ALARM. Release the
button when the wake-up hour flashes. To change the hour, press + or – .
