background image

27

TR7000i/TR8000i

Treadmill

Innovative Features (continued)

2 USB Ports:

 

The TR7000i/TR8000i includes a USB port that works with the LifeSpan Fitness Club online 

health management system. Before using the treadmill, simply insert your USB flash drive into the left USB port, 

after loading your profile from the IHP system onto the flash drive. The USB will read your personal information 

and then save your workout data every 20 seconds onto the flash drive. Information saved includes your heart 

rate, workout start and finish time, distance traveled, calories burned, and steps taken. This information can be 

uploaded into your account, summarized over time and used to compare your results with the goals you set 

in your personal LFC account. Prior to using your USB, make sure you refer to the “Getting Started Guide” and 

“Success Guide” found in your membership kit, located in your owner’s manual packet. Both ports can be used to 

charge portable devices such as iPads and cell phones. 

Don’t remove the USB flash drive while the LED light is flashing red – you may lose your workout 

information. 

Bluetooth:

 The TR7000i/TR8000i series products include a free iPad app that lets you connect wirelessly to 

view graphically your heart rate, pace on a quarter-mile track and easily sync results with your LifeSpan Fitness 

Club account. Currently LifeSpan does not have an iPhone app. However, other app developers are working on 

iPhone apps which could be available in the near future.

Energy Saving Mode:

 

The energy saving mode cuts all power to the treadmill with the exception of one 

dimly lit LED below the START button. This will cut power consumption to well under 0.1 watts. 

Cleaning and Maintenance

Daily:

 

It is recommended to wipe the treadmill down after each use to keep the treadmill clean and dry. A mild 

detergent may be used at times to help remove all dirt and salt from the belt, painted parts and the display.

Monthly:

 

This cleaning would include removing the motor cover and cleaning around the motor and 

electronics. It is recommended to clean the motor compartment if the treadmill is in an area where there might 

be plush carpet fibers that could get pulled up into the motor compartment. It is a good idea at this time to 

check and tighten all assembly hardware, power cord for damage, or anything else that would indicate the need 

for service.

Warning:

 

Unplug the power cord before removing the motor cover

Important: 

If service is required, turn the power off and remove the power cord to ensure the unit cannot be 

used. Let all other users know the unit needs service.

 Caution:

 

Acidic cleaning detergents may damage painted or powder coated surfaces and should not  

 

be used. Such cleaners may void the LifeSpan warranty.

 Suggestion:

 It is always a good idea in a commercial setting to have someone on staff or a local  

 

 

service  provider to perform periodic maintenance on the treadmill. For help finding a local service  

 

 

provider that will perform periodic maintenance, please contact customer service at 877.654.3839 x 4

 

(US and Canada only).

Summary of Contents for TR7000i


































Reviews: