background image

 

3

ELECTRICAL SAFETY 

When using an electrical appliance, basic precautions should always be followed, including 

the following: 

Read all instructions before using this unit. 

DANGER -

 To reduce the risk of electric shock: 

WARNING -

 To reduce the risk of burns, fire, electric shock, or injury to persons: 

 

1.  An appliance should never be left unattended when plugged in.    Unplug from electrical 

outlet when not in use and before putting on or cleaning. 

2.  Do not operate under blanket or pillow.    Excessive heating can occur and cause fire, 

electric shock, or injury to persons. 

3.  Close supervision is necessary when the motorized oxy cycle is used by, on, or near 

children, invalids or disabled persons. 

4.  Use the motorized oxy cycle only for its intended use as described in this manual.    Do 

not use attachments not recommended by the manufacturer. 

5.  Never operate the motorized oxy cycle if it has a damaged cord or plug.    If it is not 

working properly, if it has been dropped or damaged, or dropped into water.     

6.  Do not carry the motorized oxy cycle by supply cord or use cord as a handle. 

7.  Keep the cord away from heated surface. 

8.  Never operate the motorized oxy cycle with the air openings blocked; keep the air 

openings free of lint. 

9.  Never drop or insert any object into any opening. 

10.  Do not use outdoors. 

11.  Do not operate where aerosol (spray) products are being used or where oxygen is being 

administered. 

12.  To disconnect, turn the speed control knob to the off

 

position, then remove plug from the 

electrical outlet. 

13.  For indoors household use only. 

 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for 16062















Reviews: