Life Fitness Cable Motion 39735 Assembly Instructions Manual Download Page 25

25

LIMITED WARRANTY

Life Fitness® G7 Cable Motion™ Gym System

Life Fitness extends the following LIMITED WARRANTY to the original owner (proof of purchase required, keep your
receipt with this manual) of the Life Fitness product. The Warranty terms apply to IN HOME and LIGHT INSTITUTIONAL
USE ONLY.

1.

LIMITED WARRANTY ON FRAME AND WELDS.

If the frame of the Life Fitness product or a weld should crack

or break, it will be repaired or replaced by Life Fitness. Terms: IN HOME USE ONLY: Lifetime – for so long as the
Customer owns the Life Fitness product; LIGHT INSTITUTIONAL USE: Ten (10) years.

2.

LIMITED WARRANTY ON PARTS.

If the following parts are defective in material or workmanship, Life Fitness will

supply replacement parts: all bolts, nuts, washers, bearings, bushings, pulleys, thumbscrews, collars, cable retain-
ing clips, adjustable pre-stretch slides, roller pad shafts, allen head bolts, weight selector pin, weight stack shaft,
set screws, protector caps, adjustment chain, cotter pin, plunger, spring and knob. Terms: IN HOME USE ONLY:
Lifetime – for so long as the Customer owns the Life Fitness product; LIGHT INSTITUTIONAL USE: One (1) year.

3. 

LIMITED WARRANTY ON CABLES AND UPHOLSTERY. 

If the coated cables or upholstery are defective in mate-

rial or workmanship, Life Fitness will repair or replace them, at its option. Terms: IN HOME USE ONLY: Three (3)
years; LIGHT INSTITUTIONAL USE: Ninety (90) days.

4.

CONDITIONS AND EXCEPTIONS. 

Any product misuse, abuse or alteration, any attempt to repair by a person

other than an authorized Life Fitness Service Center, any improper assembly, accident, or any other condition
resulting from occurrences beyond the control of Life Fitness will void this Limited Warranty.

5.

REPLACEMENT AND REPAIR EXPENSES. 

Life Fitness will provide only replacement parts or repair under this

warranty. The Owner is responsible for all other costs. Such costs may include, but are not limited to: a. labor
charges for service, removal, repair or reinstallation of the Life Fitness product or any component part; b. shipping,
delivery, handling and administrative charges for returning parts to Life Fitness; and c. all necessary or incidental
costs related to installation of the replacement parts.

6.

SHIPPING.

If shipping by the Owners is deemed necessary (in sole discretion of Life Fitness), parts should be

shipped in their original carton or equivalent packaging, fully insured with shipping charges prepaid. Life Fitness
will not assume any responsibility for any loss or damage incurred in shipping.

7.

CLAIM PROCEDURES.

If service on your Life Fitness product is required during the warranty period, please con-

tact our Customer Service Department at 1-800-351-3737 (U.S. and Canada) or +1-847-288-3300 (outside of U.S.
and Canada) for instructions regarding returning or replacing parts. Please have available the following informa-
tion: (i) the dealer’s name; (ii) the date of purchase; (iii) the serial # (s) of your product(s) (the serial number loca-
tion is called out on the final assembly drawing included with your assembly instruction); (iv) a description of the
nature of the problem.

8.

OWNER’S RIGHT.

This Limited Warranty gives you specific legal rights. You may also have other rights, which

vary depending on local law.

9.

LIMITATION OF IMPLIED WARRANTIES.

All implied warranties, except to the extent prohibited by applicable law,

shall have no greater duration than the warranty period set forth above. There are no warranties which extend
beyond the description in this Limited Warranty. Because local laws do not allow limitations on how long an implied
warranty lasts, the above limitations may not apply to you.

10.

DISCLAIMER.

No other express warranty has been made or will be made on behalf of Life Fitness with respect to

any Life Fitness product or the operation, repair or replacement of any Life Fitness product. Life Fitness shall not
be responsible for injury, loss of use of the Life Fitness product, inconvenience, loss or damage to personal prop-
erty, whether direct or indirect, and incidental or consequential damages, so the above limitation or exclusion may
not apply to you.

Notes:

Summary of Contents for Cable Motion 39735



























Reviews: