background image

2

TABLE OF CONTENTS

Safety Statement  . . . . . . . . . . . . . . . .2

Required Hardware . . . . . . . . . . . . . . . .8

G7 Warning Labels  . . . . . . . . . . . . . . .4

Assembly Instructions  . . . . . . . . . . . . . .10

Gym Dimensions.  . . . . . . . . . . . . . . . .5

General Maintenance  . . . . . . . . . . . . . .24

G7 Live Area  . . . . . . . . . . . . . . . . . . .6

Warranty Statement  . . . . . . . . . . . . . . .25

Components List . . . . . . . . . . . . . . . . .7

Contact Information  . . . . . . . . . . . . . . .26

SAFETY INFORMATION

It is the sole responsibility of the purchaser of LIFE FITNESS products to read the owner's manual, warning labels and
instruct all individuals, whether they are the end user or supervising personnel on proper usage of the equipment.

UNDERSTANDING EACH AND EVERY WARNING TO THE FULLEST IS IMPORTANT. IF ANY OF THESE INSTRUC-
TIONS OR WARNINGS ARE UNCLEAR, CONTACT LIFE FITNESS CUSTOMER SERVICE IMMEDIATELY AT 1-800-
351-3737 WITHIN THE US AND CANADA. INTERNATIONAL OFFICE CONTACT INFORMATION IS AVAILABLE ON
PAGE 26.

Keep children away from strength equipment. Parent or others supervising children must provide close supervision of
children if the equipment is used in the presence of children. 

This equipment is categorized as class H per EN 957-1. And as such this equipment is only intended for Home use. It is
not intended for commercial, institutional and/or studio facilities use. Contact LIFE FITNESS with any questions regarding
this classification.

It is recommended that all users of LIFE FITNESS exercise equipment be informed of the following information prior to
use.

ACCESS CONTROL

LIFE FITNESS recommends that all fitness equipment be used in a supervised area. It is recommended that 
the equipment be located in an access controlled area. Control is the responsibility of the facility owner.

INSTALLATION

SECURING EQUIPMENT - LIFE FITNESS recommends that all equipment be secured to a solid, level 
surface to stabilize and eliminate rocking or tipping over. This must be per formed by a licensed contractor.

PROPER USAGE

1.

Do not use any equipment in any way other than as designed or intended by the manufacturer. It is 
imperative that LIFE FITNESS equipment is used properly to avoid injury.

2.

Injuries may result if exercising improperly or excessively. It is recommended that all individuals consult a
physician prior to commencing an exercise program. If at any time during exercise you feel faint, dizzy or
experience pain, STOP EXERCIZING and consult your physician. 

3.

Keep body parts (hands, feet, hair, etc.), clothing and jewelry away from moving parts to avoid injury.

4.

When adjusting any seat, knee hold down pad, range of motion limiter, foothold pad, pulley or any other 
type of adjuster, make certain that the adjusting pin is fully engaged in the hole to avoid injury. 

Summary of Contents for Cable Motion 39735



























Reviews: