manualshive.com logo in svg

LIFAN Power USA 2V77F, Manual

Share
Download
LIFAN Power USA 2V77F Manual Download Page 36

 

36 

WARNING: 

●

 

When testing the spark plug, never hold the high- voltage wire of the spark plug with wet hand. 

●

 

Make sure there is no spilled fuel outside the engine and that the spark plug isn’t dipped with fuel. 

●

 

To prevent fire, keep sparks far away from the spark plug mount hole. 

Ⅱ

. Low gasoline engine power output 

TROUBLE 

CAUSE 

REMEDY 

When turning 
throttle greater, 
speed increase 
responds 
slowly or speed 
is decreased 
even engine 
stops running. 

Ignition 
system 

Incorrect ignition time. 

Readjust 

ignition 

advance 

angle 

Fuel 
supply 
system 

Air in fuel line or fuel line clogged. 

Exhaust air or dredge fuel line 

Main oil flow hole is not adjusted properly. 

Readjust 

In  carburetor,  needle  valve  hole  and  main  oil  flow 
hole clogged. 

Clean and blow to get through 

Fuel cock is clogged up. 

Clean, replace damaged part 

Too much carbon deposit in combusting chamber. 

Clear away 

Too much car bon fouling in muffler and exhaust pipe.  Clear away 

Air cleaner is clogged up. 

Clean air cleaner filter elemei   

Intake pipe is leaking. 

Repair or replace 

Poor 
compres
sion 

Piston or cylinder or piston ring is worn. 

Replace the worn   

Air leakage from the surface by which cylinder block 
contacting with cylinder head. 

Replace cylinder gasket 

Too big or too small valve clearance. 

Readjust   

Valve tightness is poor. 

Repair   

Summary of Contents for 2V77F













































Reviews:

No comments

Brands by name

Popular brands

Load more brands